Fixed MTP to work with TWRP

Documentation/arm/OMAP/omap_pm

@@ -0,0 +1,154 @@
+
+The OMAP PM interface
+=====================
+
+This document describes the temporary OMAP PM interface.  Driver
+authors use these functions to communicate minimum latency or
+throughput constraints to the kernel power management code.
+Over time, the intention is to merge features from the OMAP PM
+interface into the Linux PM QoS code.
+
+Drivers need to express PM parameters which:
+
+- support the range of power management parameters present in the TI SRF;
+
+- separate the drivers from the underlying PM parameter
+  implementation, whether it is the TI SRF or Linux PM QoS or Linux
+  latency framework or something else;
+
+- specify PM parameters in terms of fundamental units, such as
+  latency and throughput, rather than units which are specific to OMAP
+  or to particular OMAP variants;
+
+- allow drivers which are shared with other architectures (e.g.,
+  DaVinci) to add these constraints in a way which won't affect non-OMAP
+  systems,
+
+- can be implemented immediately with minimal disruption of other
+  architectures.
+
+
+This document proposes the OMAP PM interface, including the following
+five power management functions for driver code:
+
+1. Set the maximum MPU wakeup latency:
+   (*pdata->set_max_mpu_wakeup_lat)(struct device *dev, unsigned long t)
+
+2. Set the maximum device wakeup latency:
+   (*pdata->set_max_dev_wakeup_lat)(struct device *dev, unsigned long t)
+
+3. Set the maximum system DMA transfer start latency (CORE pwrdm):
+   (*pdata->set_max_sdma_lat)(struct device *dev, long t)
+
+4. Set the minimum bus throughput needed by a device:
+   (*pdata->set_min_bus_tput)(struct device *dev, u8 agent_id, unsigned long r)
+
+5. Return the number of times the device has lost context
+   (*pdata->get_dev_context_loss_count)(struct device *dev)
+
+
+Further documentation for all OMAP PM interface functions can be
+found in arch/arm/plat-omap/include/mach/omap-pm.h.
+
+
+The OMAP PM layer is intended to be temporary
+---------------------------------------------
+
+The intention is that eventually the Linux PM QoS layer should support
+the range of power management features present in OMAP3.  As this
+happens, existing drivers using the OMAP PM interface can be modified
+to use the Linux PM QoS code; and the OMAP PM interface can disappear.
+
+
+Driver usage of the OMAP PM functions
+-------------------------------------
+
+As the 'pdata' in the above examples indicates, these functions are
+exposed to drivers through function pointers in driver .platform_data
+structures.  The function pointers are initialized by the board-*.c
+files to point to the corresponding OMAP PM functions:
+.set_max_dev_wakeup_lat will point to
+omap_pm_set_max_dev_wakeup_lat(), etc.  Other architectures which do
+not support these functions should leave these function pointers set
+to NULL.  Drivers should use the following idiom:
+
+        if (pdata->set_max_dev_wakeup_lat)
+            (*pdata->set_max_dev_wakeup_lat)(dev, t);
+
+The most common usage of these functions will probably be to specify
+the maximum time from when an interrupt occurs, to when the device
+becomes accessible.  To accomplish this, driver writers should use the
+set_max_mpu_wakeup_lat() function to constrain the MPU wakeup
+latency, and the set_max_dev_wakeup_lat() function to constrain the
+device wakeup latency (from clk_enable() to accessibility).  For
+example,
+
+        /* Limit MPU wakeup latency */
+        if (pdata->set_max_mpu_wakeup_lat)
+            (*pdata->set_max_mpu_wakeup_lat)(dev, tc);
+
+        /* Limit device powerdomain wakeup latency */
+        if (pdata->set_max_dev_wakeup_lat)
+            (*pdata->set_max_dev_wakeup_lat)(dev, td);
+
+        /* total wakeup latency in this example: (tc + td) */
+
+The PM parameters can be overwritten by calling the function again
+with the new value.  The settings can be removed by calling the
+function with a t argument of -1 (except in the case of
+set_max_bus_tput(), which should be called with an r argument of 0).
+
+The fifth function above, omap_pm_get_dev_context_loss_count(),
+is intended as an optimization to allow drivers to determine whether the
+device has lost its internal context.  If context has been lost, the
+driver must restore its internal context before proceeding.
+
+
+Other specialized interface functions
+-------------------------------------
+
+The five functions listed above are intended to be usable by any
+device driver.  DSPBridge and CPUFreq have a few special requirements.
+DSPBridge expresses target DSP performance levels in terms of OPP IDs.
+CPUFreq expresses target MPU performance levels in terms of MPU
+frequency.  The OMAP PM interface contains functions for these
+specialized cases to convert that input information (OPPs/MPU
+frequency) into the form that the underlying power management
+implementation needs:
+
+6. (*pdata->dsp_get_opp_table)(void)
+
+7. (*pdata->dsp_set_min_opp)(u8 opp_id)
+
+8. (*pdata->dsp_get_opp)(void)
+
+9. (*pdata->cpu_get_freq_table)(void)
+
+10. (*pdata->cpu_set_freq)(unsigned long f)
+
+11. (*pdata->cpu_get_freq)(void)
+
+Customizing OPP for platform
+============================
+Defining CONFIG_PM should enable OPP layer for the silicon
+and the registration of OPP table should take place automatically.
+However, in special cases, the default OPP table may need to be
+tweaked, for e.g.:
+ * enable default OPPs which are disabled by default, but which
+   could be enabled on a platform
+ * Disable an unsupported OPP on the platform
+ * Define and add a custom opp table entry
+in these cases, the board file needs to do additional steps as follows:
+arch/arm/mach-omapx/board-xyz.c
+	#include "pm.h"
+	....
+	static void __init omap_xyz_init_irq(void)
+	{
+		....
+		/* Initialize the default table */
+		omapx_opp_init();
+		/* Do customization to the defaults */
+		....
+	}
+NOTE: omapx_opp_init will be omap3_opp_init or as required
+based on the omap family.