Fixed MTP to work with TWRP

Documentation/cpu-freq/cpu-drivers.txt

@@ -0,0 +1,274 @@
+     CPU frequency and voltage scaling code in the Linux(TM) kernel
+
+
+		         L i n u x    C P U F r e q
+
+			   C P U   D r i v e r s 
+
+		       - information for developers -
+
+
+		    Dominik Brodowski  <linux@brodo.de>
+
+
+
+   Clock scaling allows you to change the clock speed of the CPUs on the
+    fly. This is a nice method to save battery power, because the lower
+            the clock speed, the less power the CPU consumes.
+
+
+Contents:
+---------
+1.   What To Do?
+1.1  Initialization
+1.2  Per-CPU Initialization
+1.3  verify
+1.4  target/target_index or setpolicy?
+1.5  target/target_index
+1.6  setpolicy
+1.7  get_intermediate and target_intermediate
+2.   Frequency Table Helpers
+
+
+
+1. What To Do?
+==============
+
+So, you just got a brand-new CPU / chipset with datasheets and want to
+add cpufreq support for this CPU / chipset? Great. Here are some hints
+on what is necessary:
+
+
+1.1 Initialization
+------------------
+
+First of all, in an __initcall level 7 (module_init()) or later
+function check whether this kernel runs on the right CPU and the right
+chipset. If so, register a struct cpufreq_driver with the CPUfreq core
+using cpufreq_register_driver()
+
+What shall this struct cpufreq_driver contain? 
+
+cpufreq_driver.name -		The name of this driver.
+
+cpufreq_driver.init -		A pointer to the per-CPU initialization 
+				function.
+
+cpufreq_driver.verify -		A pointer to a "verification" function.
+
+cpufreq_driver.setpolicy _or_ 
+cpufreq_driver.target/
+target_index		-	See below on the differences.
+
+And optionally
+
+cpufreq_driver.exit -		A pointer to a per-CPU cleanup
+				function called during CPU_POST_DEAD
+				phase of cpu hotplug process.
+
+cpufreq_driver.stop_cpu -	A pointer to a per-CPU stop function
+				called during CPU_DOWN_PREPARE phase of
+				cpu hotplug process.
+
+cpufreq_driver.resume -		A pointer to a per-CPU resume function
+				which is called with interrupts disabled
+				and _before_ the pre-suspend frequency
+				and/or policy is restored by a call to
+				->target/target_index or ->setpolicy.
+
+cpufreq_driver.attr -		A pointer to a NULL-terminated list of
+				"struct freq_attr" which allow to
+				export values to sysfs.
+
+cpufreq_driver.get_intermediate
+and target_intermediate		Used to switch to stable frequency while
+				changing CPU frequency.
+
+
+1.2 Per-CPU Initialization
+--------------------------
+
+Whenever a new CPU is registered with the device model, or after the
+cpufreq driver registers itself, the per-CPU initialization function 
+cpufreq_driver.init is called. It takes a struct cpufreq_policy
+*policy as argument. What to do now?
+
+If necessary, activate the CPUfreq support on your CPU.
+
+Then, the driver must fill in the following values:
+
+policy->cpuinfo.min_freq _and_
+policy->cpuinfo.max_freq -	the minimum and maximum frequency 
+				(in kHz) which is supported by 
+				this CPU
+policy->cpuinfo.transition_latency   the time it takes on this CPU to
+				switch between two frequencies in
+				nanoseconds (if appropriate, else
+				specify CPUFREQ_ETERNAL)
+
+policy->cur			The current operating frequency of
+				this CPU (if appropriate)
+policy->min, 
+policy->max, 
+policy->policy and, if necessary,
+policy->governor		must contain the "default policy" for
+				this CPU. A few moments later,
+				cpufreq_driver.verify and either
+				cpufreq_driver.setpolicy or
+				cpufreq_driver.target/target_index is called
+				with these values.
+
+For setting some of these values (cpuinfo.min[max]_freq, policy->min[max]), the
+frequency table helpers might be helpful. See the section 2 for more information
+on them.
+
+SMP systems normally have same clock source for a group of cpus. For these the
+.init() would be called only once for the first online cpu. Here the .init()
+routine must initialize policy->cpus with mask of all possible cpus (Online +
+Offline) that share the clock. Then the core would copy this mask onto
+policy->related_cpus and will reset policy->cpus to carry only online cpus.
+
+
+1.3 verify
+------------
+
+When the user decides a new policy (consisting of
+"policy,governor,min,max") shall be set, this policy must be validated
+so that incompatible values can be corrected. For verifying these
+values, a frequency table helper and/or the
+cpufreq_verify_within_limits(struct cpufreq_policy *policy, unsigned
+int min_freq, unsigned int max_freq) function might be helpful. See
+section 2 for details on frequency table helpers.
+
+You need to make sure that at least one valid frequency (or operating
+range) is within policy->min and policy->max. If necessary, increase
+policy->max first, and only if this is no solution, decrease policy->min.
+
+
+1.4 target/target_index or setpolicy?
+----------------------------
+
+Most cpufreq drivers or even most cpu frequency scaling algorithms 
+only allow the CPU to be set to one frequency. For these, you use the
+->target/target_index call.
+
+Some cpufreq-capable processors switch the frequency between certain
+limits on their own. These shall use the ->setpolicy call
+
+
+1.5. target/target_index
+-------------
+
+The target_index call has two arguments: struct cpufreq_policy *policy,
+and unsigned int index (into the exposed frequency table).
+
+The CPUfreq driver must set the new frequency when called here. The
+actual frequency must be determined by freq_table[index].frequency.
+
+It should always restore to earlier frequency (i.e. policy->restore_freq) in
+case of errors, even if we switched to intermediate frequency earlier.
+
+Deprecated:
+----------
+The target call has three arguments: struct cpufreq_policy *policy,
+unsigned int target_frequency, unsigned int relation.
+
+The CPUfreq driver must set the new frequency when called here. The
+actual frequency must be determined using the following rules:
+
+- keep close to "target_freq"
+- policy->min <= new_freq <= policy->max (THIS MUST BE VALID!!!)
+- if relation==CPUFREQ_REL_L, try to select a new_freq higher than or equal
+  target_freq. ("L for lowest, but no lower than")
+- if relation==CPUFREQ_REL_H, try to select a new_freq lower than or equal
+  target_freq. ("H for highest, but no higher than")
+
+Here again the frequency table helper might assist you - see section 2
+for details.
+
+
+1.6 setpolicy
+---------------
+
+The setpolicy call only takes a struct cpufreq_policy *policy as
+argument. You need to set the lower limit of the in-processor or
+in-chipset dynamic frequency switching to policy->min, the upper limit
+to policy->max, and -if supported- select a performance-oriented
+setting when policy->policy is CPUFREQ_POLICY_PERFORMANCE, and a
+powersaving-oriented setting when CPUFREQ_POLICY_POWERSAVE. Also check
+the reference implementation in drivers/cpufreq/longrun.c
+
+1.7 get_intermediate and target_intermediate
+--------------------------------------------
+
+Only for drivers with target_index() and CPUFREQ_ASYNC_NOTIFICATION unset.
+
+get_intermediate should return a stable intermediate frequency platform wants to
+switch to, and target_intermediate() should set CPU to to that frequency, before
+jumping to the frequency corresponding to 'index'. Core will take care of
+sending notifications and driver doesn't have to handle them in
+target_intermediate() or target_index().
+
+Drivers can return '0' from get_intermediate() in case they don't wish to switch
+to intermediate frequency for some target frequency. In that case core will
+directly call ->target_index().
+
+NOTE: ->target_index() should restore to policy->restore_freq in case of
+failures as core would send notifications for that.
+
+
+2. Frequency Table Helpers
+==========================
+
+As most cpufreq processors only allow for being set to a few specific
+frequencies, a "frequency table" with some functions might assist in
+some work of the processor driver. Such a "frequency table" consists
+of an array of struct cpufreq_frequency_table entries, with any value in
+"driver_data" you want to use, and the corresponding frequency in
+"frequency". At the end of the table, you need to add a
+cpufreq_frequency_table entry with frequency set to CPUFREQ_TABLE_END. And
+if you want to skip one entry in the table, set the frequency to 
+CPUFREQ_ENTRY_INVALID. The entries don't need to be in ascending
+order.
+
+By calling cpufreq_frequency_table_cpuinfo(struct cpufreq_policy *policy,
+					struct cpufreq_frequency_table *table);
+the cpuinfo.min_freq and cpuinfo.max_freq values are detected, and
+policy->min and policy->max are set to the same values. This is
+helpful for the per-CPU initialization stage.
+
+int cpufreq_frequency_table_verify(struct cpufreq_policy *policy,
+                                   struct cpufreq_frequency_table *table);
+assures that at least one valid frequency is within policy->min and
+policy->max, and all other criteria are met. This is helpful for the
+->verify call.
+
+int cpufreq_frequency_table_target(struct cpufreq_policy *policy,
+                                   struct cpufreq_frequency_table *table,
+                                   unsigned int target_freq,
+                                   unsigned int relation,
+                                   unsigned int *index);
+
+is the corresponding frequency table helper for the ->target
+stage. Just pass the values to this function, and the unsigned int
+index returns the number of the frequency table entry which contains
+the frequency the CPU shall be set to.
+
+The following macros can be used as iterators over cpufreq_frequency_table:
+
+cpufreq_for_each_entry(pos, table) - iterates over all entries of frequency
+table.
+
+cpufreq-for_each_valid_entry(pos, table) - iterates over all entries,
+excluding CPUFREQ_ENTRY_INVALID frequencies.
+Use arguments "pos" - a cpufreq_frequency_table * as a loop cursor and
+"table" - the cpufreq_frequency_table * you want to iterate over.
+
+For example:
+
+	struct cpufreq_frequency_table *pos, *driver_freq_table;
+
+	cpufreq_for_each_entry(pos, driver_freq_table) {
+		/* Do something with pos */
+		pos->frequency = ...
+	}