Fixed MTP to work with TWRP

Documentation/devicetree/bindings/clock/ti/apll.txt

@@ -0,0 +1,45 @@
+Binding for Texas Instruments APLL clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1].  It assumes a
+register-mapped APLL with usually two selectable input clocks
+(reference clock and bypass clock), with analog phase locked
+loop logic for multiplying the input clock to a desired output
+clock. This clock also typically supports different operation
+modes (locked, low power stop etc.) APLL mostly behaves like
+a subtype of a DPLL [2], although a simplified one at that.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/clock/ti/dpll.txt
+
+Required properties:
+- compatible : shall be "ti,dra7-apll-clock" or "ti,omap2-apll-clock"
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : link phandles of parent clocks (clk-ref and clk-bypass)
+- reg : address and length of the register set for controlling the APLL.
+  It contains the information of registers in the following order:
+	"control" - contains the control register offset
+	"idlest" - contains the idlest register offset
+	"autoidle" - contains the autoidle register offset (OMAP2 only)
+- ti,clock-frequency : static clock frequency for the clock (OMAP2 only)
+- ti,idlest-shift : bit-shift for the idlest field (OMAP2 only)
+- ti,bit-shift : bit-shift for enable and autoidle fields (OMAP2 only)
+
+Examples:
+	apll_pcie_ck: apll_pcie_ck {
+		#clock-cells = <0>;
+		clocks = <&apll_pcie_in_clk_mux>, <&dpll_pcie_ref_ck>;
+		reg = <0x021c>, <0x0220>;
+		compatible = "ti,dra7-apll-clock";
+	};
+
+	apll96_ck: apll96_ck {
+		#clock-cells = <0>;
+		compatible = "ti,omap2-apll-clock";
+		clocks = <&sys_ck>;
+		ti,bit-shift = <2>;
+		ti,idlest-shift = <8>;
+		ti,clock-frequency = <96000000>;
+		reg = <0x0500>, <0x0530>, <0x0520>;
+	};

Documentation/devicetree/bindings/clock/ti/autoidle.txt

@@ -0,0 +1,39 @@
+Binding for Texas Instruments autoidle clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1]. It assumes a register mapped
+clock which can be put to idle automatically by hardware based on the usage
+and a configuration bit setting. Autoidle clock is never an individual
+clock, it is always a derivative of some basic clock like a gate, divider,
+or fixed-factor.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- reg : offset for the register controlling the autoidle
+- ti,autoidle-shift : bit shift of the autoidle enable bit
+- ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0
+
+Examples:
+	dpll_core_m4_ck: dpll_core_m4_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_core_x2_ck>;
+		ti,max-div = <31>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2d38>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	dpll_usb_clkdcoldo_ck: dpll_usb_clkdcoldo_ck {
+		#clock-cells = <0>;
+		compatible = "ti,fixed-factor-clock";
+		clocks = <&dpll_usb_ck>;
+		ti,clock-div = <1>;
+		ti,autoidle-shift = <8>;
+		reg = <0x01b4>;
+		ti,clock-mult = <1>;
+		ti,invert-autoidle-bit;
+	};

Documentation/devicetree/bindings/clock/ti/clockdomain.txt

@@ -0,0 +1,24 @@
+Binding for Texas Instruments clockdomain.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1] in consumer role.
+Every clock on TI SoC belongs to one clockdomain, but software
+only needs this information for specific clocks which require
+their parent clockdomain to be controlled when the clock is
+enabled/disabled. This binding doesn't define a new clock
+binding type, it is used to group existing clock nodes under
+hardware hierarchy.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be "ti,clockdomain"
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : link phandles of clocks within this domain
+
+Examples:
+	dss_clkdm: dss_clkdm {
+		compatible = "ti,clockdomain";
+		clocks = <&dss1_alwon_fck_3430es2>, <&dss_ick_3430es2>;
+	};

Documentation/devicetree/bindings/clock/ti/composite.txt

@@ -0,0 +1,54 @@
+Binding for TI composite clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1]. It assumes a
+register-mapped composite clock with multiple different sub-types;
+
+a multiplexer clock with multiple input clock signals or parents, one
+of which can be selected as output, this behaves exactly as [2]
+
+an adjustable clock rate divider, this behaves exactly as [3]
+
+a gating function which can be used to enable and disable the output
+clock, this behaves exactly as [4]
+
+The binding must provide a list of the component clocks that shall be
+merged to this clock. The component clocks shall be of one of the
+"ti,*composite*-clock" types.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/clock/ti/mux.txt
+[3] Documentation/devicetree/bindings/clock/ti/divider.txt
+[4] Documentation/devicetree/bindings/clock/ti/gate.txt
+
+Required properties:
+- compatible : shall be: "ti,composite-clock"
+- clocks : link phandles of component clocks
+- #clock-cells : from common clock binding; shall be set to 0.
+
+Examples:
+
+usb_l4_gate_ick: usb_l4_gate_ick {
+	#clock-cells = <0>;
+	compatible = "ti,composite-interface-clock";
+	clocks = <&l4_ick>;
+	ti,bit-shift = <5>;
+	reg = <0x0a10>;
+};
+
+usb_l4_div_ick: usb_l4_div_ick {
+	#clock-cells = <0>;
+	compatible = "ti,composite-divider-clock";
+	clocks = <&l4_ick>;
+	ti,bit-shift = <4>;
+	ti,max-div = <1>;
+	reg = <0x0a40>;
+	ti,index-starts-at-one;
+};
+
+usb_l4_ick: usb_l4_ick {
+	#clock-cells = <0>;
+	compatible = "ti,composite-clock";
+	clocks = <&usb_l4_gate_ick>, <&usb_l4_div_ick>;
+};

Documentation/devicetree/bindings/clock/ti/divider.txt

@@ -0,0 +1,114 @@
+Binding for TI divider clock
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1].  It assumes a
+register-mapped adjustable clock rate divider that does not gate and has
+only one input clock or parent.  By default the value programmed into
+the register is one less than the actual divisor value.  E.g:
+
+register value		actual divisor value
+0			1
+1			2
+2			3
+
+This assumption may be modified by the following optional properties:
+
+ti,index-starts-at-one - valid divisor values start at 1, not the default
+of 0.  E.g:
+register value		actual divisor value
+1			1
+2			2
+3			3
+
+ti,index-power-of-two - valid divisor values are powers of two.  E.g:
+register value		actual divisor value
+0			1
+1			2
+2			4
+
+Additionally an array of valid dividers may be supplied like so:
+
+	ti,dividers = <4>, <8>, <0>, <16>;
+
+Which will map the resulting values to a divisor table by their index:
+register value		actual divisor value
+0			4
+1			8
+2			<invalid divisor, skipped>
+3			16
+
+Any zero value in this array means the corresponding bit-value is invalid
+and must not be used.
+
+The binding must also provide the register to control the divider and
+unless the divider array is provided, min and max dividers. Optionally
+the number of bits to shift that mask, if necessary. If the shift value
+is missing it is the same as supplying a zero shift.
+
+This binding can also optionally provide support to the hardware autoidle
+feature, see [2].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/clock/ti/autoidle.txt
+
+Required properties:
+- compatible : shall be "ti,divider-clock" or "ti,composite-divider-clock".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : link to phandle of parent clock
+- reg : offset for register controlling adjustable divider
+
+Optional properties:
+- clock-output-names : from common clock binding.
+- ti,dividers : array of integers defining divisors
+- ti,bit-shift : number of bits to shift the divider value, defaults to 0
+- ti,min-div : min divisor for dividing the input clock rate, only
+  needed if the first divisor is offset from the default value (1)
+- ti,max-div : max divisor for dividing the input clock rate, only needed
+  if ti,dividers is not defined.
+- ti,index-starts-at-one : valid divisor programming starts at 1, not zero,
+  only valid if ti,dividers is not defined.
+- ti,index-power-of-two : valid divisor programming must be a power of two,
+  only valid if ti,dividers is not defined.
+- ti,autoidle-shift : bit shift of the autoidle enable bit for the clock,
+  see [2]
+- ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0,
+  see [2]
+- ti,set-rate-parent : clk_set_rate is propagated to parent
+
+Examples:
+dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 {
+	#clock-cells = <0>;
+	compatible = "ti,divider-clock";
+	clocks = <&dpll_usb_ck>;
+	ti,max-div = <127>;
+	reg = <0x190>;
+	ti,index-starts-at-one;
+};
+
+aess_fclk: aess_fclk@4a004528 {
+	#clock-cells = <0>;
+	compatible = "ti,divider-clock";
+	clocks = <&abe_clk>;
+	ti,bit-shift = <24>;
+	reg = <0x528>;
+	ti,max-div = <2>;
+};
+
+dpll_core_m3x2_div_ck: dpll_core_m3x2_div_ck {
+	#clock-cells = <0>;
+	compatible = "ti,composite-divider-clock";
+	clocks = <&dpll_core_x2_ck>;
+	ti,max-div = <31>;
+	reg = <0x0134>;
+	ti,index-starts-at-one;
+};
+
+ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2 {
+	#clock-cells = <0>;
+	compatible = "ti,composite-divider-clock";
+	clocks = <&corex2_fck>;
+	ti,bit-shift = <8>;
+	reg = <0x0a40>;
+	ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+};

Documentation/devicetree/bindings/clock/ti/dpll.txt

@@ -0,0 +1,85 @@
+Binding for Texas Instruments DPLL clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1].  It assumes a
+register-mapped DPLL with usually two selectable input clocks
+(reference clock and bypass clock), with digital phase locked
+loop logic for multiplying the input clock to a desired output
+clock. This clock also typically supports different operation
+modes (locked, low power stop etc.) This binding has several
+sub-types, which effectively result in slightly different setup
+for the actual DPLL clock.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be one of:
+		"ti,omap3-dpll-clock",
+		"ti,omap3-dpll-core-clock",
+		"ti,omap3-dpll-per-clock",
+		"ti,omap3-dpll-per-j-type-clock",
+		"ti,omap4-dpll-clock",
+		"ti,omap4-dpll-x2-clock",
+		"ti,omap4-dpll-core-clock",
+		"ti,omap4-dpll-m4xen-clock",
+		"ti,omap4-dpll-j-type-clock",
+		"ti,omap5-mpu-dpll-clock",
+		"ti,am3-dpll-no-gate-clock",
+		"ti,am3-dpll-j-type-clock",
+		"ti,am3-dpll-no-gate-j-type-clock",
+		"ti,am3-dpll-clock",
+		"ti,am3-dpll-core-clock",
+		"ti,am3-dpll-x2-clock",
+		"ti,omap2-dpll-core-clock",
+
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : link phandles of parent clocks, first entry lists reference clock
+  and second entry bypass clock
+- reg : offsets for the register set for controlling the DPLL.
+  Registers are listed in following order:
+	"control" - contains the control register base address
+	"idlest" - contains the idle status register base address
+	"mult-div1" - contains the multiplier / divider register base address
+	"autoidle" - contains the autoidle register base address (optional)
+  ti,am3-* dpll types do not have autoidle register
+  ti,omap2-* dpll type does not support idlest / autoidle registers
+
+Optional properties:
+- DPLL mode setting - defining any one or more of the following overrides
+  default setting.
+	- ti,low-power-stop : DPLL supports low power stop mode, gating output
+	- ti,low-power-bypass : DPLL output matches rate of parent bypass clock
+	- ti,lock : DPLL locks in programmed rate
+
+Examples:
+	dpll_core_ck: dpll_core_ck@44e00490 {
+		#clock-cells = <0>;
+		compatible = "ti,omap4-dpll-core-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x490>, <0x45c>, <0x488>, <0x468>;
+	};
+
+	dpll2_ck: dpll2_ck@48004004 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-dpll-clock";
+		clocks = <&sys_ck>, <&dpll2_fck>;
+		ti,low-power-stop;
+		ti,low-power-bypass;
+		ti,lock;
+		reg = <0x4>, <0x24>, <0x34>, <0x40>;
+	};
+
+	dpll_core_ck: dpll_core_ck@44e00490 {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-core-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x90>, <0x5c>, <0x68>;
+	};
+
+	dpll_ck: dpll_ck {
+		#clock-cells = <0>;
+		compatible = "ti,omap2-dpll-core-clock";
+		clocks = <&sys_ck>, <&sys_ck>;
+		reg = <0x0500>, <0x0540>;
+	};

Documentation/devicetree/bindings/clock/ti/dra7-atl.txt

@@ -0,0 +1,96 @@
+Device Tree Clock bindings for ATL (Audio Tracking Logic) of DRA7 SoC.
+
+The ATL IP is used to generate clock to be used to synchronize baseband and
+audio codec. A single ATL IP provides four ATL clock instances sharing the same
+functional clock but can be configured to provide different clocks.
+ATL can maintain a clock averages to some desired frequency based on the bws/aws
+signals - can compensate the drift between the two ws signal.
+
+In order to provide the support for ATL and it's output clocks (which can be used
+internally within the SoC or external components) two sets of bindings is needed:
+
+Clock tree binding:
+This binding uses the common clock binding[1].
+To be able to integrate the ATL clocks with DT clock tree.
+Provides ccf level representation of the ATL clocks to be used by drivers.
+Since the clock instances are part of a single IP this binding is used as a node
+for the DT clock tree, the IP driver is needed to handle the actual configuration
+of the IP.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be "ti,dra7-atl-clock"
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : link phandles to functional clock of ATL
+
+Binding for the IP driver:
+This binding is used to configure the IP driver which is going to handle the
+configuration of the IP for the ATL clock instances.
+
+Required properties:
+- compatible : shall be "ti,dra7-atl"
+- reg : base address for the ATL IP
+- ti,provided-clocks : List of phandles to the clocks associated with the ATL
+- clocks : link phandles to functional clock of ATL
+- clock-names : Shall be set to "fck"
+- ti,hwmods : Shall be set to "atl"
+
+Optional properties:
+Configuration of ATL instances:
+- atl{0/1/2/3} {
+	- bws : Baseband word select signal selection
+	- aws : Audio word select signal selection
+};
+
+For valid word select signals, see the dt-bindings/clk/ti-dra7-atl.h include
+file.
+
+Examples:
+/* clock bindings for atl provided clocks */
+atl_clkin0_ck: atl_clkin0_ck {
+	#clock-cells = <0>;
+	compatible = "ti,dra7-atl-clock";
+	clocks = <&atl_gfclk_mux>;
+};
+
+atl_clkin1_ck: atl_clkin1_ck {
+	#clock-cells = <0>;
+	compatible = "ti,dra7-atl-clock";
+	clocks = <&atl_gfclk_mux>;
+};
+
+atl_clkin2_ck: atl_clkin2_ck {
+	#clock-cells = <0>;
+	compatible = "ti,dra7-atl-clock";
+	clocks = <&atl_gfclk_mux>;
+};
+
+atl_clkin3_ck: atl_clkin3_ck {
+	#clock-cells = <0>;
+	compatible = "ti,dra7-atl-clock";
+	clocks = <&atl_gfclk_mux>;
+};
+
+/* binding for the IP */
+atl: atl@4843c000 {
+	compatible = "ti,dra7-atl";
+	reg = <0x4843c000 0x3ff>;
+	ti,hwmods = "atl";
+	ti,provided-clocks = <&atl_clkin0_ck>, <&atl_clkin1_ck>,
+				<&atl_clkin2_ck>, <&atl_clkin3_ck>;
+	clocks = <&atl_gfclk_mux>;
+	clock-names = "fck";
+	status = "disabled";
+};
+
+#include <dt-bindings/clk/ti-dra7-atl.h>
+
+&atl {
+	status = "okay";
+
+	atl2 {
+		bws = <DRA7_ATL_WS_MCASP2_FSX>;
+		aws = <DRA7_ATL_WS_MCASP3_FSX>;
+	};
+};

Documentation/devicetree/bindings/clock/ti/fixed-factor-clock.txt

@@ -0,0 +1,43 @@
+Binding for TI fixed factor rate clock sources.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1], and also uses the autoidle
+support from TI autoidle clock [2].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/clock/ti/autoidle.txt
+
+Required properties:
+- compatible : shall be "ti,fixed-factor-clock".
+- #clock-cells : from common clock binding; shall be set to 0.
+- ti,clock-div: fixed divider.
+- ti,clock-mult: fixed multiplier.
+- clocks: parent clock.
+
+Optional properties:
+- ti,autoidle-shift: bit shift of the autoidle enable bit for the clock,
+  see [2]
+- reg: offset for the autoidle register of this clock, see [2]
+- ti,invert-autoidle-bit: autoidle is enabled by setting the bit to 0, see [2]
+- ti,set-rate-parent: clk_set_rate is propagated to parent
+
+Example:
+	clock {
+		compatible = "ti,fixed-factor-clock";
+		clocks = <&parentclk>;
+		#clock-cells = <0>;
+		ti,clock-div = <2>;
+		ti,clock-mult = <1>;
+	};
+
+	dpll_usb_clkdcoldo_ck: dpll_usb_clkdcoldo_ck {
+		#clock-cells = <0>;
+		compatible = "ti,fixed-factor-clock";
+		clocks = <&dpll_usb_ck>;
+		ti,clock-div = <1>;
+		ti,autoidle-shift = <8>;
+		reg = <0x01b4>;
+		ti,clock-mult = <1>;
+		ti,invert-autoidle-bit;
+	};

Documentation/devicetree/bindings/clock/ti/gate.txt

@@ -0,0 +1,106 @@
+Binding for Texas Instruments gate clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1]. This clock is
+quite much similar to the basic gate-clock [2], however,
+it supports a number of additional features. If no register
+is provided for this clock, the code assumes that a clockdomain
+will be controlled instead and the corresponding hw-ops for
+that is used.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/clock/gate-clock.txt
+[3] Documentation/devicetree/bindings/clock/ti/clockdomain.txt
+
+Required properties:
+- compatible : shall be one of:
+  "ti,gate-clock" - basic gate clock
+  "ti,wait-gate-clock" - gate clock which waits until clock is active before
+			 returning from clk_enable()
+  "ti,dss-gate-clock" - gate clock with DSS specific hardware handling
+  "ti,am35xx-gate-clock" - gate clock with AM35xx specific hardware handling
+  "ti,clkdm-gate-clock" - clockdomain gate clock, which derives its functional
+			  clock directly from a clockdomain, see [3] how
+			  to map clockdomains properly
+  "ti,hsdiv-gate-clock" - gate clock with OMAP36xx specific hardware handling,
+			  required for a hardware errata
+  "ti,composite-gate-clock" - composite gate clock, to be part of composite
+			      clock
+  "ti,composite-no-wait-gate-clock" - composite gate clock that does not wait
+				      for clock to be active before returning
+				      from clk_enable()
+- #clock-cells : from common clock binding; shall be set to 0
+- clocks : link to phandle of parent clock
+- reg : offset for register controlling adjustable gate, not needed for
+	ti,clkdm-gate-clock type
+
+Optional properties:
+- ti,bit-shift : bit shift for programming the clock gate, invalid for
+		 ti,clkdm-gate-clock type
+- ti,set-bit-to-disable : inverts default gate programming. Setting the bit
+  gates the clock and clearing the bit ungates the clock.
+
+Examples:
+	mmchs2_fck: mmchs2_fck@48004a00 {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&core_96m_fck>;
+		reg = <0x0a00>;
+		ti,bit-shift = <25>;
+	};
+
+	uart4_fck_am35xx: uart4_fck_am35xx {
+		#clock-cells = <0>;
+		compatible = "ti,wait-gate-clock";
+		clocks = <&core_48m_fck>;
+		reg = <0x0a00>;
+		ti,bit-shift = <23>;
+	};
+
+	dss1_alwon_fck_3430es2: dss1_alwon_fck_3430es2@48004e00 {
+		#clock-cells = <0>;
+		compatible = "ti,dss-gate-clock";
+		clocks = <&dpll4_m4x2_ck>;
+		reg = <0x0e00>;
+		ti,bit-shift = <0>;
+	};
+
+	emac_ick: emac_ick@4800259c {
+		#clock-cells = <0>;
+		compatible = "ti,am35xx-gate-clock";
+		clocks = <&ipss_ick>;
+		reg = <0x059c>;
+		ti,bit-shift = <1>;
+	};
+
+	emu_src_ck: emu_src_ck {
+		#clock-cells = <0>;
+		compatible = "ti,clkdm-gate-clock";
+		clocks = <&emu_src_mux_ck>;
+	};
+
+	dpll4_m2x2_ck: dpll4_m2x2_ck@48004d00 {
+		#clock-cells = <0>;
+		compatible = "ti,hsdiv-gate-clock";
+		clocks = <&dpll4_m2x2_mul_ck>;
+		ti,bit-shift = <0x1b>;
+		reg = <0x0d00>;
+		ti,set-bit-to-disable;
+	};
+
+	vlynq_gate_fck: vlynq_gate_fck {
+		#clock-cells = <0>;
+		compatible = "ti,composite-gate-clock";
+		clocks = <&core_ck>;
+		ti,bit-shift = <3>;
+		reg = <0x0200>;
+	};
+
+	sys_clkout2_src_gate: sys_clkout2_src_gate {
+		#clock-cells = <0>;
+		compatible = "ti,composite-no-wait-gate-clock";
+		clocks = <&core_ck>;
+		ti,bit-shift = <15>;
+		reg = <0x0070>;
+	};

Documentation/devicetree/bindings/clock/ti/interface.txt

@@ -0,0 +1,56 @@
+Binding for Texas Instruments interface clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1]. This clock is
+quite much similar to the basic gate-clock [2], however,
+it supports a number of additional features, including
+companion clock finding (match corresponding functional gate
+clock) and hardware autoidle enable / disable.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+[2] Documentation/devicetree/bindings/clock/gate-clock.txt
+
+Required properties:
+- compatible : shall be one of:
+  "ti,omap3-interface-clock" - basic OMAP3 interface clock
+  "ti,omap3-no-wait-interface-clock" - interface clock which has no hardware
+				       capability for waiting clock to be ready
+  "ti,omap3-hsotgusb-interface-clock" - interface clock with USB specific HW
+					handling
+  "ti,omap3-dss-interface-clock" - interface clock with DSS specific HW handling
+  "ti,omap3-ssi-interface-clock" - interface clock with SSI specific HW handling
+  "ti,am35xx-interface-clock" - interface clock with AM35xx specific HW handling
+  "ti,omap2430-interface-clock" - interface clock with OMAP2430 specific HW
+				  handling
+- #clock-cells : from common clock binding; shall be set to 0
+- clocks : link to phandle of parent clock
+- reg : base address for the control register
+
+Optional properties:
+- ti,bit-shift : bit shift for the bit enabling/disabling the clock (default 0)
+
+Examples:
+	aes1_ick: aes1_ick@48004a14 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-interface-clock";
+		clocks = <&security_l4_ick2>;
+		reg = <0x48004a14 0x4>;
+		ti,bit-shift = <3>;
+	};
+
+	cam_ick: cam_ick@48004f10 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-no-wait-interface-clock";
+		clocks = <&l4_ick>;
+		reg = <0x48004f10 0x4>;
+		ti,bit-shift = <0>;
+	};
+
+	ssi_ick_3430es2: ssi_ick_3430es2@48004a10 {
+		#clock-cells = <0>;
+		compatible = "ti,omap3-ssi-interface-clock";
+		clocks = <&ssi_l4_ick>;
+		reg = <0x48004a10 0x4>;
+		ti,bit-shift = <0>;
+	};

Documentation/devicetree/bindings/clock/ti/mux.txt

@@ -0,0 +1,76 @@
+Binding for TI mux clock.
+
+Binding status: Unstable - ABI compatibility may be broken in the future
+
+This binding uses the common clock binding[1].  It assumes a
+register-mapped multiplexer with multiple input clock signals or
+parents, one of which can be selected as output.  This clock does not
+gate or adjust the parent rate via a divider or multiplier.
+
+By default the "clocks" property lists the parents in the same order
+as they are programmed into the regster.  E.g:
+
+	clocks = <&foo_clock>, <&bar_clock>, <&baz_clock>;
+
+results in programming the register as follows:
+
+register value		selected parent clock
+0			foo_clock
+1			bar_clock
+2			baz_clock
+
+Some clock controller IPs do not allow a value of zero to be programmed
+into the register, instead indexing begins at 1.  The optional property
+"index-starts-at-one" modified the scheme as follows:
+
+register value		selected clock parent
+1			foo_clock
+2			bar_clock
+3			baz_clock
+
+The binding must provide the register to control the mux. Optionally
+the number of bits to shift the control field in the register can be
+supplied. If the shift value is missing it is the same as supplying
+a zero shift.
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be "ti,mux-clock" or "ti,composite-mux-clock".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : link phandles of parent clocks
+- reg : register offset for register controlling adjustable mux
+
+Optional properties:
+- ti,bit-shift : number of bits to shift the bit-mask, defaults to
+  0 if not present
+- ti,index-starts-at-one : valid input select programming starts at 1, not
+  zero
+- ti,set-rate-parent : clk_set_rate is propagated to parent clock,
+  not supported by the composite-mux-clock subtype
+
+Examples:
+
+sys_clkin_ck: sys_clkin_ck@4a306110 {
+	#clock-cells = <0>;
+	compatible = "ti,mux-clock";
+	clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>;
+	reg = <0x0110>;
+	ti,index-starts-at-one;
+};
+
+abe_dpll_bypass_clk_mux_ck: abe_dpll_bypass_clk_mux_ck@4a306108 {
+	#clock-cells = <0>;
+	compatible = "ti,mux-clock";
+	clocks = <&sys_clkin_ck>, <&sys_32k_ck>;
+	ti,bit-shift = <24>;
+	reg = <0x0108>;
+};
+
+mcbsp5_mux_fck: mcbsp5_mux_fck {
+	#clock-cells = <0>;
+	compatible = "ti,composite-mux-clock";
+	clocks = <&core_96m_fck>, <&mcbsp_clks>;
+	ti,bit-shift = <4>;
+	reg = <0x02d8>;
+};