Fixed MTP to work with TWRP

Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt

@@ -0,0 +1,22 @@
+Broadcom BCM2835 SPI0 controller
+
+The BCM2835 contains two forms of SPI master controller, one known simply as
+SPI0, and the other known as the "Universal SPI Master"; part of the
+auxiliary block. This binding applies to the SPI0 controller.
+
+Required properties:
+- compatible: Should be "brcm,bcm2835-spi".
+- reg: Should contain register location and length.
+- interrupts: Should contain interrupt.
+- clocks: The clock feeding the SPI controller.
+
+Example:
+
+spi@20204000 {
+	compatible = "brcm,bcm2835-spi";
+	reg = <0x7e204000 0x1000>;
+	interrupts = <2 22>;
+	clocks = <&clk_spi>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};

Documentation/devicetree/bindings/spi/efm32-spi.txt

@@ -0,0 +1,41 @@
+* Energy Micro EFM32 SPI
+
+Required properties:
+- #address-cells: see spi-bus.txt
+- #size-cells: see spi-bus.txt
+- compatible: should be "energymicro,efm32-spi"
+- reg: Offset and length of the register set for the controller
+- interrupts: pair specifying rx and tx irq
+- clocks: phandle to the spi clock
+- cs-gpios: see spi-bus.txt
+
+Recommended properties :
+- energymicro,location: Value to write to the ROUTE register's LOCATION
+                        bitfield to configure the pinmux for the device, see
+                        datasheet for values.
+                        If this property is not provided, keeping what is
+                        already configured in the hardware, so its either the
+                        reset default 0 or whatever the bootloader did.
+
+Example:
+
+spi1: spi@0x4000c400 { /* USART1 */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "energymicro,efm32-spi";
+	reg = <0x4000c400 0x400>;
+	interrupts = <15 16>;
+	clocks = <&cmu 20>;
+	cs-gpios = <&gpio 51 1>; // D3
+	energymicro,location = <1>;
+	status = "ok";
+
+	ks8851@0 {
+		compatible = "ks8851";
+		spi-max-frequency = <6000000>;
+		reg = <0>;
+		interrupt-parent = <&boardfpga>;
+		interrupts = <4>;
+		status = "ok";
+	};
+};

Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt

@@ -0,0 +1,27 @@
+* Freescale (Enhanced) Configurable Serial Peripheral Interface
+  (CSPI/eCSPI) for i.MX
+
+Required properties:
+- compatible : Should be "fsl,<soc>-cspi" or "fsl,<soc>-ecspi"
+- reg : Offset and length of the register set for the device
+- interrupts : Should contain CSPI/eCSPI interrupt
+- fsl,spi-num-chipselects : Contains the number of the chipselect
+- cs-gpios : Specifies the gpio pins to be used for chipselects.
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+		Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request names should include "tx" and "rx" if present.
+
+Example:
+
+ecspi@70010000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx51-ecspi";
+	reg = <0x70010000 0x4000>;
+	interrupts = <36>;
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */
+		   <&gpio3 25 0>; /* GPIO3_25 */
+	dmas = <&sdma 3 7 1>, <&sdma 4 7 2>;
+	dma-names = "rx", "tx";
+};

Documentation/devicetree/bindings/spi/fsl-spi.txt

@@ -0,0 +1,60 @@
+* SPI (Serial Peripheral Interface)
+
+Required properties:
+- cell-index : QE SPI subblock index.
+		0: QE subblock SPI1
+		1: QE subblock SPI2
+- compatible : should be "fsl,spi" or "aeroflexgaisler,spictrl".
+- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+  field that represents an encoding of the sense and level
+  information for the interrupt.  This should be encoded based on
+  the information in section 2) depending on the type of interrupt
+  controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+  services interrupts for this device.
+- clock-frequency : input clock frequency to non FSL_SOC cores
+
+Optional properties:
+- gpios : specifies the gpio pins to be used for chipselects.
+  The gpios will be referred to as reg = <index> in the SPI child nodes.
+  If unspecified, a single SPI device without a chip select can be used.
+
+Example:
+	spi@4c0 {
+		cell-index = <0>;
+		compatible = "fsl,spi";
+		reg = <4c0 40>;
+		interrupts = <82 0>;
+		interrupt-parent = <700>;
+		mode = "cpu";
+		gpios = <&gpio 18 1	// device reg=<0>
+			 &gpio 19 1>;	// device reg=<1>
+	};
+
+
+* eSPI (Enhanced Serial Peripheral Interface)
+
+Required properties:
+- compatible : should be "fsl,mpc8536-espi".
+- reg : Offset and length of the register set for the device.
+- interrupts : should contain eSPI interrupt, the device has one interrupt.
+- fsl,espi-num-chipselects : the number of the chipselect signals.
+
+Optional properties:
+- fsl,csbef: chip select assertion time in bits before frame starts
+- fsl,csaft: chip select negation time in bits after frame ends
+
+Example:
+	spi@110000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc8536-espi";
+		reg = <0x110000 0x1000>;
+		interrupts = <53 0x2>;
+		interrupt-parent = <&mpic>;
+		fsl,espi-num-chipselects = <4>;
+		fsl,csbef = <1>;
+		fsl,csaft = <1>;
+	};

Documentation/devicetree/bindings/spi/mxs-spi.txt

@@ -0,0 +1,26 @@
+* Freescale MX233/MX28 SSP/SPI
+
+Required properties:
+- compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28"
+- reg: Offset and length of the register set for the device
+- interrupts: Should contain SSP ERROR interrupt
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and SSP DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
+
+Optional properties:
+- clock-frequency : Input clock frequency to the SPI block in Hz.
+		    Default is 160000000 Hz.
+
+Example:
+
+ssp0: ssp@80010000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	reg = <0x80010000 0x2000>;
+	interrupts = <96>;
+	dmas = <&dma_apbh 0>;
+	dma-names = "rx-tx";
+};

Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt

@@ -0,0 +1,40 @@
+NVIDIA Tegra114 SPI controller.
+
+Required properties:
+- compatible : should be "nvidia,tegra114-spi".
+- reg: Should contain SPI registers location and length.
+- interrupts: Should contain SPI interrupts.
+- clock-names : Must include the following entries:
+  - spi
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - spi
+- dmas : Must contain an entry for each entry in clock-names.
+  See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+  - rx
+  - tx
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+
+Recommended properties:
+- spi-max-frequency: Definition as per
+                     Documentation/devicetree/bindings/spi/spi-bus.txt
+Example:
+
+spi@7000d600 {
+	compatible = "nvidia,tegra114-spi";
+	reg = <0x7000d600 0x200>;
+	interrupts = <0 82 0x04>;
+	spi-max-frequency = <25000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clocks = <&tegra_car 44>;
+	clock-names = "spi";
+	resets = <&tegra_car 44>;
+	reset-names = "spi";
+	dmas = <&apbdma 16>, <&apbdma 16>;
+	dma-names = "rx", "tx";
+	status = "disabled";
+};

Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt

@@ -0,0 +1,38 @@
+NVIDIA Tegra20 SFLASH controller.
+
+Required properties:
+- compatible : should be "nvidia,tegra20-sflash".
+- reg: Should contain SFLASH registers location and length.
+- interrupts: Should contain SFLASH interrupts.
+- clocks : Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - spi
+- dmas : Must contain an entry for each entry in clock-names.
+  See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+  - rx
+  - tx
+
+Recommended properties:
+- spi-max-frequency: Definition as per
+                     Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+spi@7000c380 {
+	compatible = "nvidia,tegra20-sflash";
+	reg = <0x7000c380 0x80>;
+	interrupts = <0 39 0x04>;
+	spi-max-frequency = <25000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clocks = <&tegra_car 43>;
+	resets = <&tegra_car 43>;
+	reset-names = "spi";
+	dmas = <&apbdma 11>, <&apbdma 11>;
+	dma-names = "rx", "tx";
+	status = "disabled";
+};

Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt

@@ -0,0 +1,38 @@
+NVIDIA Tegra20/Tegra30 SLINK controller.
+
+Required properties:
+- compatible : should be "nvidia,tegra20-slink", "nvidia,tegra30-slink".
+- reg: Should contain SLINK registers location and length.
+- interrupts: Should contain SLINK interrupts.
+- clocks : Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - spi
+- dmas : Must contain an entry for each entry in clock-names.
+  See ../dma/dma.txt for details.
+- dma-names : Must include the following entries:
+  - rx
+  - tx
+
+Recommended properties:
+- spi-max-frequency: Definition as per
+                     Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+spi@7000d600 {
+	compatible = "nvidia,tegra20-slink";
+	reg = <0x7000d600 0x200>;
+	interrupts = <0 82 0x04>;
+	spi-max-frequency = <25000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clocks = <&tegra_car 44>;
+	resets = <&tegra_car 44>;
+	reset-names = "spi";
+	dmas = <&apbdma 16>, <&apbdma 16>;
+	dma-names = "rx", "tx";
+	status = "disabled";
+};

Documentation/devicetree/bindings/spi/omap-spi.txt

@@ -0,0 +1,47 @@
+OMAP2+ McSPI device
+
+Required properties:
+- compatible :
+  - "ti,omap2-mcspi" for OMAP2 & OMAP3.
+  - "ti,omap4-mcspi" for OMAP4+.
+- ti,spi-num-cs : Number of chipselect supported  by the instance.
+- ti,hwmods: Name of the hwmod associated to the McSPI
+- ti,pindir-d0-out-d1-in: Select the D0 pin as output and D1 as
+			  input. The default is D0 as input and
+			  D1 as output.
+
+Optional properties:
+- dmas: List of DMA specifiers with the controller specific format
+	as described in the generic DMA client binding. A tx and rx
+	specifier is required for each chip select.
+- dma-names: List of DMA request names. These strings correspond
+	1:1 with the DMA specifiers listed in dmas. The string naming
+	is to be "rxN" and "txN" for RX and TX requests,
+	respectively, where N equals the chip select number.
+
+Examples:
+
+[hwmod populated DMA resources]
+
+mcspi1: mcspi@1 {
+    #address-cells = <1>;
+    #size-cells = <0>;
+    compatible = "ti,omap4-mcspi";
+    ti,hwmods = "mcspi1";
+    ti,spi-num-cs = <4>;
+};
+
+[generic DMA request binding]
+
+mcspi1: mcspi@1 {
+    #address-cells = <1>;
+    #size-cells = <0>;
+    compatible = "ti,omap4-mcspi";
+    ti,hwmods = "mcspi1";
+    ti,spi-num-cs = <2>;
+    dmas = <&edma 42
+	    &edma 43
+	    &edma 44
+	    &edma 45>;
+    dma-names = "tx0", "rx0", "tx1", "rx1";
+};

Documentation/devicetree/bindings/spi/qcom,spi-qup.txt

@@ -0,0 +1,95 @@
+Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
+
+The QUP core is an AHB slave that provides a common data path (an output FIFO
+and an input FIFO) for serial peripheral interface (SPI) mini-core.
+
+SPI in master mode supports up to 50MHz, up to four chip selects, programmable
+data path from 4 bits to 32 bits and numerous protocol variants.
+
+Required properties:
+- compatible:     Should contain:
+		  "qcom,spi-qup-v1.1.1" for 8660, 8960 and 8064.
+		  "qcom,spi-qup-v2.1.1" for 8974 and later
+		  "qcom,spi-qup-v2.2.1" for 8974 v2 and later.
+
+- reg:            Should contain base register location and length
+- interrupts:     Interrupt number used by this controller
+
+- clocks:         Should contain the core clock and the AHB clock.
+- clock-names:    Should be "core" for the core clock and "iface" for the
+                  AHB clock.
+
+- #address-cells: Number of cells required to define a chip select
+                  address on the SPI bus. Should be set to 1.
+- #size-cells:    Should be zero.
+
+Optional properties:
+- spi-max-frequency: Specifies maximum SPI clock frequency,
+                     Units - Hz. Definition as per
+                     Documentation/devicetree/bindings/spi/spi-bus.txt
+- num-cs:	total number of chipselects
+- cs-gpios:	should specify GPIOs used for chipselects.
+		The gpios will be referred to as reg = <index> in the SPI child
+		nodes.  If unspecified, a single SPI device without a chip
+		select can be used.
+
+
+SPI slave nodes must be children of the SPI master node and can contain
+properties described in Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+	spi_8: spi@f9964000 { /* BLSP2 QUP2 */
+
+		compatible = "qcom,spi-qup-v2";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0xf9964000 0x1000>;
+		interrupts = <0 102 0>;
+		spi-max-frequency = <19200000>;
+
+		clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+		clock-names = "core", "iface";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi8_default>;
+
+		device@0 {
+			compatible = "arm,pl022-dummy";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0>; /* Chip select 0 */
+			spi-max-frequency = <19200000>;
+			spi-cpol;
+		};
+
+		device@1 {
+			compatible = "arm,pl022-dummy";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <1>; /* Chip select 1 */
+			spi-max-frequency = <9600000>;
+			spi-cpha;
+		};
+
+		device@2 {
+			compatible = "arm,pl022-dummy";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <2>; /* Chip select 2 */
+			spi-max-frequency = <19200000>;
+			spi-cpol;
+			spi-cpha;
+		};
+
+		device@3 {
+			compatible = "arm,pl022-dummy";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <3>; /* Chip select 3 */
+			spi-max-frequency = <19200000>;
+			spi-cpol;
+			spi-cpha;
+			spi-cs-high;
+		};
+	};

Documentation/devicetree/bindings/spi/sh-hspi.txt

@@ -0,0 +1,29 @@
+Renesas HSPI.
+
+Required properties:
+- compatible       : "renesas,hspi-<soctype>", "renesas,hspi" as fallback.
+		     Examples with soctypes are:
+		       - "renesas,hspi-r8a7778" (R-Car M1)
+		       - "renesas,hspi-r8a7779" (R-Car H1)
+- reg              : Offset and length of the register set for the device
+- interrupt-parent : The phandle for the interrupt controller that
+		     services interrupts for this device
+- interrupts       : Interrupt specifier
+- #address-cells   : Must be <1>
+- #size-cells      : Must be <0>
+
+Pinctrl properties might be needed, too.  See
+Documentation/devicetree/bindings/pinctrl/renesas,*.
+
+Example:
+
+	hspi0: spi@fffc7000 {
+		compatible = "renesas,hspi-r8a7778", "renesas,hspi";
+		reg = <0xfffc7000 0x18>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+

Documentation/devicetree/bindings/spi/sh-msiof.txt

@@ -0,0 +1,55 @@
+Renesas MSIOF spi controller
+
+Required properties:
+- compatible           : "renesas,msiof-<soctype>" for SoCs,
+			 "renesas,sh-msiof" for SuperH, or
+			 "renesas,sh-mobile-msiof" for SH Mobile series.
+			 Examples with soctypes are:
+			 "renesas,msiof-r8a7790" (R-Car H2)
+			 "renesas,msiof-r8a7791" (R-Car M2-W)
+			 "renesas,msiof-r8a7792" (R-Car V2H)
+			 "renesas,msiof-r8a7793" (R-Car M2-N)
+			 "renesas,msiof-r8a7794" (R-Car E2)
+- reg                  : A list of offsets and lengths of the register sets for
+			 the device.
+			 If only one register set is present, it is to be used
+			 by both the CPU and the DMA engine.
+			 If two register sets are present, the first is to be
+			 used by the CPU, and the second is to be used by the
+			 DMA engine.
+- interrupt-parent     : The phandle for the interrupt controller that
+			 services interrupts for this device
+- interrupts           : Interrupt specifier
+- #address-cells       : Must be <1>
+- #size-cells          : Must be <0>
+
+Optional properties:
+- clocks               : Must contain a reference to the functional clock.
+- num-cs               : Total number of chip-selects (default is 1)
+- dmas                 : Must contain a list of two references to DMA
+			 specifiers, one for transmission, and one for
+			 reception.
+- dma-names            : Must contain a list of two DMA names, "tx" and "rx".
+
+Optional properties, deprecated for soctype-specific bindings:
+- renesas,tx-fifo-size : Overrides the default tx fifo size given in words
+			 (default is 64)
+- renesas,rx-fifo-size : Overrides the default rx fifo size given in words
+			 (default is 64, or 256 on R-Car Gen2)
+
+Pinctrl properties might be needed, too.  See
+Documentation/devicetree/bindings/pinctrl/renesas,*.
+
+Example:
+
+	msiof0: spi@e6e20000 {
+		compatible = "renesas,msiof-r8a7791";
+		reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>;
+		interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
+		dmas = <&dmac0 0x51>, <&dmac0 0x52>;
+		dma-names = "tx", "rx";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};

Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt

@@ -0,0 +1,28 @@
+Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface.
+
+Required properties:
+- compatible : "snps,dw-apb-ssi"
+- reg : The register base for the controller.
+- interrupts : One interrupt, used by the controller.
+- #address-cells : <1>, as required by generic SPI binding.
+- #size-cells : <0>, also as required by generic SPI binding.
+
+Optional properties:
+- cs-gpios : Specifies the gpio pis to be used for chipselects.
+- num-cs : The number of chipselects. If omitted, this will default to 4.
+
+Child nodes as per the generic SPI binding.
+
+Example:
+
+	spi@fff00000 {
+		compatible = "snps,dw-apb-ssi";
+		reg = <0xfff00000 0x1000>;
+		interrupts = <0 154 4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		num-cs = <2>;
+		cs-gpios = <&gpio0 13 0>,
+			   <&gpio0 14 0>;
+	};
+

Documentation/devicetree/bindings/spi/spi-bus.txt

@@ -0,0 +1,94 @@
+SPI (Serial Peripheral Interface) busses
+
+SPI busses can be described with a node for the SPI master device
+and a set of child nodes for each SPI slave on the bus.  For this
+discussion, it is assumed that the system's SPI controller is in
+SPI master mode.  This binding does not describe SPI controllers
+in slave mode.
+
+The SPI master node requires the following properties:
+- #address-cells  - number of cells required to define a chip select
+    		address on the SPI bus.
+- #size-cells     - should be zero.
+- compatible      - name of SPI bus controller following generic names
+    		recommended practice.
+- cs-gpios	  - (optional) gpios chip select.
+No other properties are required in the SPI bus node.  It is assumed
+that a driver for an SPI bus device will understand that it is an SPI bus.
+However, the binding does not attempt to define the specific method for
+assigning chip select numbers.  Since SPI chip select configuration is
+flexible and non-standardized, it is left out of this binding with the
+assumption that board specific platform code will be used to manage
+chip selects.  Individual drivers can define additional properties to
+support describing the chip select layout.
+
+Optional property:
+- num-cs : total number of chipselects
+
+If cs-gpios is used the number of chip select will automatically increased
+with max(cs-gpios > hw cs)
+
+So if for example the controller has 2 CS lines, and the cs-gpios
+property looks like this:
+
+cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>;
+
+Then it should be configured so that num_chipselect = 4 with the
+following mapping:
+
+cs0 : &gpio1 0 0
+cs1 : native
+cs2 : &gpio1 1 0
+cs3 : &gpio1 2 0
+
+SPI slave nodes must be children of the SPI master node and can
+contain the following properties.
+- reg             - (required) chip select address of device.
+- compatible      - (required) name of SPI device following generic names
+    		recommended practice
+- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
+- spi-cpol        - (optional) Empty property indicating device requires
+    		inverse clock polarity (CPOL) mode
+- spi-cpha        - (optional) Empty property indicating device requires
+    		shifted clock phase (CPHA) mode
+- spi-cs-high     - (optional) Empty property indicating device requires
+    		chip select active high
+- spi-3wire       - (optional) Empty property indicating device requires
+    		    3-wire mode.
+- spi-lsb-first   - (optional) Empty property indicating device requires
+		LSB first mode.
+- spi-tx-bus-width - (optional) The bus width(number of data wires) that
+                      used for MOSI. Defaults to 1 if not present.
+- spi-rx-bus-width - (optional) The bus width(number of data wires) that
+                      used for MISO. Defaults to 1 if not present.
+
+Some SPI controllers and devices support Dual and Quad SPI transfer mode.
+It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD).
+Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is
+only 1(SINGLE), 2(DUAL) and 4(QUAD).
+Dual/Quad mode is not allowed when 3-wire mode is used.
+
+If a gpio chipselect is used for the SPI slave the gpio number will be passed
+via the SPI master node cs-gpios property.
+
+SPI example for an MPC5200 SPI bus:
+	spi@f00 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+		reg = <0xf00 0x20>;
+		interrupts = <2 13 0 2 14 0>;
+		interrupt-parent = <&mpc5200_pic>;
+
+		ethernet-switch@0 {
+			compatible = "micrel,ks8995m";
+			spi-max-frequency = <1000000>;
+			reg = <0>;
+		};
+
+		codec@1 {
+			compatible = "ti,tlv320aic26";
+			spi-max-frequency = <100000>;
+			reg = <1>;
+		};
+	};

Documentation/devicetree/bindings/spi/spi-cadence.txt

@@ -0,0 +1,31 @@
+Cadence SPI controller Device Tree Bindings
+-------------------------------------------
+
+Required properties:
+- compatible		: Should be "cdns,spi-r1p6" or "xlnx,zynq-spi-r1p6".
+- reg			: Physical base address and size of SPI registers map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- interrupt-parent	: Must be core interrupt controller
+- clock-names		: List of input clock names - "ref_clk", "pclk"
+			  (See clock bindings for details).
+- clocks		: Clock phandles (see clock bindings for details).
+
+Optional properties:
+- num-cs		: Number of chip selects used.
+			  If a decoder is used, this will be the number of
+			  chip selects after the decoder.
+- is-decoded-cs		: Flag to indicate whether decoder is used or not.
+
+Example:
+
+	spi@e0007000 {
+		compatible = "xlnx,zynq-spi-r1p6";
+		clock-names = "ref_clk", "pclk";
+		clocks = <&clkc 26>, <&clkc 35>;
+		interrupt-parent = <&intc>;
+		interrupts = <0 49 4>;
+		num-cs = <4>;
+		is-decoded-cs = <0>;
+		reg = <0xe0007000 0x1000>;
+	} ;

Documentation/devicetree/bindings/spi/spi-davinci.txt

@@ -0,0 +1,88 @@
+Davinci SPI controller device bindings
+
+Links on DM:
+Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf
+dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf
+OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
+
+Required properties:
+- #address-cells: number of cells required to define a chip select
+	address on the SPI bus. Should be set to 1.
+- #size-cells: should be zero.
+- compatible:
+	- "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family
+	- "ti,da830-spi" for SPI used similar to that on DA8xx SoC family
+- reg: Offset and length of SPI controller register space
+- num-cs: Number of chip selects. This includes internal as well as
+	GPIO chip selects.
+- ti,davinci-spi-intr-line: interrupt line used to connect the SPI
+	IP to the interrupt controller within the SoC. Possible values
+	are 0 and 1. Manual says one of the two possible interrupt
+	lines can be tied to the interrupt controller. Set this
+	based on a specifc SoC configuration.
+- interrupts: interrupt number mapped to CPU.
+- clocks: spi clk phandle
+
+Optional:
+- cs-gpios: gpio chip selects
+	For example to have 3 internal CS and 2 GPIO CS, user could define
+	cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>;
+	where first three are internal CS and last two are GPIO CS.
+
+Optional properties for slave devices:
+SPI slave nodes can contain the following properties.
+Not all SPI Peripherals from Texas Instruments support this.
+Please check SPI peripheral documentation for a device before using these.
+
+- ti,spi-wdelay : delay between transmission of words
+	(SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module
+	clock periods.
+
+	delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period
+
+Below is timing diagram which shows functional meaning of
+"ti,spi-wdelay" parameter.
+
+             +-+ +-+ +-+ +-+ +-+                           +-+ +-+ +-+
+SPI_CLK      | | | | | | | | | |                           | | | | | |
+  +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +-
+
+SPI_SOMI/SIMO+-----------------+                           +-----------
+  +----------+ word1           +---------------------------+word2
+             +-----------------+                           +-----------
+                                          WDELAY
+                                <-------------------------->
+
+Example of a NOR flash slave device (n25q032) connected to DaVinci
+SPI controller device over the SPI bus.
+
+spi0:spi@20BF0000 {
+	#address-cells			= <1>;
+	#size-cells			= <0>;
+	compatible			= "ti,dm6446-spi";
+	reg				= <0x20BF0000 0x1000>;
+	num-cs				= <4>;
+	ti,davinci-spi-intr-line	= <0>;
+	interrupts			= <338>;
+	clocks				= <&clkspi>;
+
+	flash: n25q032@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p32";
+		spi-max-frequency = <25000000>;
+		reg = <0>;
+		ti,spi-wdelay = <8>;
+
+		partition@0 {
+			label = "u-boot-spl";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@1 {
+			label = "test";
+			reg = <0x80000 0x380000>;
+		};
+	};
+};

Documentation/devicetree/bindings/spi/spi-dw.txt

@@ -0,0 +1,24 @@
+Synopsys DesignWare SPI master
+
+Required properties:
+- compatible: should be "snps,designware-spi"
+- #address-cells: see spi-bus.txt
+- #size-cells: see spi-bus.txt
+- reg: address and length of the spi master registers
+- interrupts: should contain one interrupt
+- clocks: spi clock phandle
+- num-cs: see spi-bus.txt
+
+Optional properties:
+- cs-gpios: see spi-bus.txt
+
+Example:
+
+spi: spi@4020a000 {
+	compatible = "snps,designware-spi";
+	interrupts = <11 1>;
+	reg = <0x4020a000 0x1000>;
+	clocks = <&pclk>;
+	num-cs = <2>;
+	cs-gpios = <&banka 0 0>;
+};

Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt

@@ -0,0 +1,49 @@
+ARM Freescale DSPI controller
+
+Required properties:
+- compatible : "fsl,vf610-dspi"
+- reg : Offset and length of the register set for the device
+- interrupts : Should contain SPI controller interrupt
+- clocks: from common clock binding: handle to dspi clock.
+- clock-names: from common clock binding: Shall be "dspi".
+- pinctrl-0: pin control group to be used for this controller.
+- pinctrl-names: must contain a "default" entry.
+- spi-num-chipselects : the number of the chipselect signals.
+- bus-num : the slave chip chipselect signal number.
+
+Optional property:
+- big-endian: If present the dspi device's registers are implemented
+  in big endian mode, otherwise in native mode(same with CPU), for more
+  detail please see: Documentation/devicetree/bindings/regmap/regmap.txt.
+
+Example:
+
+dspi0@4002c000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,vf610-dspi";
+	reg = <0x4002c000 0x1000>;
+	interrupts = <0 67 0x04>;
+	clocks = <&clks VF610_CLK_DSPI0>;
+	clock-names = "dspi";
+	spi-num-chipselects = <5>;
+	bus-num = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dspi0_1>;
+	big-endian;
+	status = "okay";
+
+	sflash: at26df081a@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "atmel,at26df081a";
+		spi-max-frequency = <16000000>;
+		spi-cpol;
+		spi-cpha;
+		reg = <0>;
+		linux,modalias = "m25p80";
+		modal = "at26df081a";
+	};
+};
+
+

Documentation/devicetree/bindings/spi/spi-gpio.txt

@@ -0,0 +1,29 @@
+SPI-GPIO devicetree bindings
+
+Required properties:
+
+ - compatible: should be set to "spi-gpio"
+ - #address-cells: should be set to <0x1>
+ - ranges
+ - gpio-sck: GPIO spec for the SCK line to use
+ - gpio-miso: GPIO spec for the MISO line to use
+ - gpio-mosi: GPIO spec for the MOSI line to use
+ - cs-gpios: GPIOs to use for chipselect lines
+ - num-chipselects: number of chipselect lines
+
+Example:
+
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <0x1>;
+		ranges;
+
+		gpio-sck = <&gpio 95 0>;
+		gpio-miso = <&gpio 98 0>;
+		gpio-mosi = <&gpio 97 0>;
+		cs-gpios = <&gpio 125 0>;
+		num-chipselects = <1>;
+
+		/* clients */
+	};
+

Documentation/devicetree/bindings/spi/spi-octeon.txt

@@ -0,0 +1,33 @@
+Cavium, Inc. OCTEON SOC SPI master controller.
+
+Required properties:
+- compatible : "cavium,octeon-3010-spi"
+- reg : The register base for the controller.
+- interrupts : One interrupt, used by the controller.
+- #address-cells : <1>, as required by generic SPI binding.
+- #size-cells : <0>, also as required by generic SPI binding.
+
+Child nodes as per the generic SPI binding.
+
+Example:
+
+	spi@1070000001000 {
+		compatible = "cavium,octeon-3010-spi";
+		reg = <0x10700 0x00001000 0x0 0x100>;
+		interrupts = <0 58>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eeprom@0 {
+			compatible = "st,m95256", "atmel,at25";
+			reg = <0>;
+			spi-max-frequency = <5000000>;
+			spi-cpha;
+			spi-cpol;
+
+			pagesize = <64>;
+			size = <32768>;
+			address-width = <16>;
+		};
+	};
+

Documentation/devicetree/bindings/spi/spi-orion.txt

@@ -0,0 +1,19 @@
+Marvell Orion SPI device
+
+Required properties:
+- compatible : should be "marvell,orion-spi" or "marvell,armada-370-spi".
+- reg : offset and length of the register set for the device
+- cell-index : Which of multiple SPI controllers is this.
+Optional properties:
+- interrupts : Is currently not used.
+
+Example:
+       spi@10600 {
+	       compatible = "marvell,orion-spi";
+	       #address-cells = <1>;
+	       #size-cells = <0>;
+	       cell-index = <0>;
+	       reg = <0x10600 0x28>;
+	       interrupts = <23>;
+	       status = "disabled";
+       };

Documentation/devicetree/bindings/spi/spi-rockchip.txt

@@ -0,0 +1,41 @@
+* Rockchip SPI Controller
+
+The Rockchip SPI controller is used to interface with various devices such as flash
+and display controllers using the SPI communication interface.
+
+Required Properties:
+
+- compatible: should be one of the following.
+    "rockchip,rk3066-spi" for rk3066.
+    "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188.
+    "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288.
+- reg: physical base address of the controller and length of memory mapped
+       region.
+- interrupts: The interrupt number to the cpu. The interrupt specifier format
+              depends on the interrupt controller.
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Shall be "spiclk" for the transfer-clock, and "apb_pclk" for
+			   the peripheral clock.
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+
+Optional Properties:
+
+- dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
+		Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: DMA request names should include "tx" and "rx" if present.
+
+
+Example:
+
+	spi0: spi@ff110000 {
+		compatible = "rockchip,rk3066-spi";
+		reg = <0xff110000 0x1000>;
+		dmas = <&pdma1 11>, <&pdma1 12>;
+		dma-names = "tx", "rx";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
+		clock-names = "spiclk", "apb_pclk";
+	};

Documentation/devicetree/bindings/spi/spi-rspi.txt

@@ -0,0 +1,69 @@
+Device tree configuration for Renesas RSPI/QSPI driver
+
+Required properties:
+- compatible       : For Renesas Serial Peripheral Interface on legacy SH:
+		     "renesas,rspi-<soctype>", "renesas,rspi" as fallback.
+		     For Renesas Serial Peripheral Interface on RZ/A1H:
+		     "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback.
+		     For Quad Serial Peripheral Interface on R-Car Gen2:
+		     "renesas,qspi-<soctype>", "renesas,qspi" as fallback.
+		     Examples with soctypes are:
+		        - "renesas,rspi-sh7757" (SH)
+			- "renesas,rspi-r7s72100" (RZ/A1H)
+			- "renesas,qspi-r8a7790" (R-Car H2)
+			- "renesas,qspi-r8a7791" (R-Car M2-W)
+			- "renesas,qspi-r8a7792" (R-Car V2H)
+			- "renesas,qspi-r8a7793" (R-Car M2-N)
+			- "renesas,qspi-r8a7794" (R-Car E2)
+- reg              : Address start and address range size of the device
+- interrupts       : A list of interrupt-specifiers, one for each entry in
+		     interrupt-names.
+		     If interrupt-names is not present, an interrupt specifier
+		     for a single muxed interrupt.
+- interrupt-names  : A list of interrupt names. Should contain (if present):
+		       - "error" for SPEI,
+		       - "rx" for SPRI,
+		       - "tx" to SPTI,
+		       - "mux" for a single muxed interrupt.
+- interrupt-parent : The phandle for the interrupt controller that
+		     services interrupts for this device.
+- num-cs	   : Number of chip selects. Some RSPI cores have more than 1.
+- #address-cells   : Must be <1>
+- #size-cells      : Must be <0>
+
+Optional properties:
+- clocks           : Must contain a reference to the functional clock.
+- dmas             : Must contain a list of two references to DMA specifiers,
+		     one for transmission, and one for reception.
+- dma-names        : Must contain a list of two DMA names, "tx" and "rx".
+
+Pinctrl properties might be needed, too.  See
+Documentation/devicetree/bindings/pinctrl/renesas,*.
+
+Examples:
+
+	spi0: spi@e800c800 {
+		compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz";
+		reg = <0xe800c800 0x24>;
+		interrupts = <0 238 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 239 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 240 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "error", "rx", "tx";
+		interrupt-parent = <&gic>;
+		num-cs = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi: spi@e6b10000 {
+		compatible = "renesas,qspi-r8a7791", "renesas,qspi";
+		reg = <0 0xe6b10000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>;
+		num-cs = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dmas = <&dmac0 0x17>, <&dmac0 0x18>;
+		dma-names = "tx", "rx";
+	};

Documentation/devicetree/bindings/spi/spi-samsung.txt

@@ -0,0 +1,109 @@
+* Samsung SPI Controller
+
+The Samsung SPI controller is used to interface with various devices such as flash
+and display controllers using the SPI communication interface.
+
+Required SoC Specific Properties:
+
+- compatible: should be one of the following.
+    - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
+    - samsung,s3c6410-spi: for s3c6410 platforms
+    - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
+    - samsung,exynos4210-spi: for exynos4 and exynos5 platforms
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- interrupts: The interrupt number to the cpu. The interrupt specifier format
+  depends on the interrupt controller.
+
+- dmas : Two or more DMA channel specifiers following the convention outlined
+  in bindings/dma/dma.txt
+
+- dma-names: Names for the dma channels. There must be at least one channel
+  named "tx" for transmit and named "rx" for receive.
+
+Required Board Specific Properties:
+
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+
+Optional Board Specific Properties:
+
+- samsung,spi-src-clk: If the spi controller includes a internal clock mux to
+  select the clock source for the spi bus clock, this property can be used to
+  indicate the clock to be used for driving the spi bus clock. If not specified,
+  the clock number 0 is used as default.
+
+- num-cs: Specifies the number of chip select lines supported. If
+  not specified, the default number of chip select lines is set to 1.
+
+- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt)
+
+SPI Controller specific data in SPI slave nodes:
+
+- The spi slave nodes should provide the following information which is required
+  by the spi controller.
+
+  - samsung,spi-feedback-delay: The sampling phase shift to be applied on the
+    miso line (to account for any lag in the miso line). The following are the
+    valid values.
+
+      - 0: No phase shift.
+      - 1: 90 degree phase shift sampling.
+      - 2: 180 degree phase shift sampling.
+      - 3: 270 degree phase shift sampling.
+
+Aliases:
+
+- All the SPI controller nodes should be represented in the aliases node using
+  the following format 'spi{n}' where n is a unique number for the alias.
+
+
+Example:
+
+- SoC Specific Portion:
+
+	spi_0: spi@12d20000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d20000 0x100>;
+		interrupts = <0 66 0>;
+		dmas = <&pdma0 5
+			&pdma0 4>;
+		dma-names = "tx", "rx";
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+- Board Specific Portion:
+
+	spi_0: spi@12d20000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi0_bus>;
+		cs-gpios = <&gpa2 5 0>;
+
+		w25q80bw@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "w25x80";
+			reg = <0>;
+			spi-max-frequency = <10000>;
+
+			controller-data {
+				samsung,spi-feedback-delay = <0>;
+			};
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "Kernel";
+				reg = <0x40000 0xc0000>;
+			};
+		};
+	};

Documentation/devicetree/bindings/spi/spi-sc18is602.txt

@@ -0,0 +1,23 @@
+NXP SC18IS602/SCIS603
+
+Required properties:
+	- compatible : Should be one of
+		"nxp,sc18is602"
+		"nxp,sc18is602b"
+		"nxp,sc18is603"
+	- reg: I2C bus address
+
+Optional properties:
+	- clock-frequency : external oscillator clock frequency. If not
+	  specified, the SC18IS602 default frequency (7372000) will be used.
+
+The clock-frequency property is relevant and needed only if the chip has an
+external oscillator (SC18IS603).
+
+Example:
+
+	sc18is603@28 {
+		compatible = "nxp,sc18is603";
+		reg = <0x28>;
+		clock-frequency = <14744000>;
+	}

Documentation/devicetree/bindings/spi/spi-sun4i.txt

@@ -0,0 +1,24 @@
+Allwinner A10 SPI controller
+
+Required properties:
+- compatible: Should be "allwinner,sun4-a10-spi".
+- reg: Should contain register location and length.
+- interrupts: Should contain interrupt.
+- clocks: phandle to the clocks feeding the SPI controller. Two are
+          needed:
+  - "ahb": the gated AHB parent clock
+  - "mod": the parent module clock
+- clock-names: Must contain the clock names described just above
+
+Example:
+
+spi1: spi@01c06000 {
+	compatible = "allwinner,sun4i-a10-spi";
+	reg = <0x01c06000 0x1000>;
+	interrupts = <11>;
+	clocks = <&ahb_gates 21>, <&spi1_clk>;
+	clock-names = "ahb", "mod";
+	status = "disabled";
+	#address-cells = <1>;
+	#size-cells = <0>;
+};

Documentation/devicetree/bindings/spi/spi-sun6i.txt

@@ -0,0 +1,24 @@
+Allwinner A31 SPI controller
+
+Required properties:
+- compatible: Should be "allwinner,sun6i-a31-spi".
+- reg: Should contain register location and length.
+- interrupts: Should contain interrupt.
+- clocks: phandle to the clocks feeding the SPI controller. Two are
+          needed:
+  - "ahb": the gated AHB parent clock
+  - "mod": the parent module clock
+- clock-names: Must contain the clock names described just above
+- resets: phandle to the reset controller asserting this device in
+          reset
+
+Example:
+
+spi1: spi@01c69000 {
+	compatible = "allwinner,sun6i-a31-spi";
+	reg = <0x01c69000 0x1000>;
+	interrupts = <0 66 4>;
+	clocks = <&ahb1_gates 21>, <&spi1_clk>;
+	clock-names = "ahb", "mod";
+	resets = <&ahb1_rst 21>;
+};

Documentation/devicetree/bindings/spi/spi-xtensa-xtfpga.txt

@@ -0,0 +1,9 @@
+Cadence Xtensa XTFPGA platform SPI controller.
+
+This simple SPI master controller is built into xtfpga bitstreams and is used
+to control daughterboard audio codec.
+
+Required properties:
+- compatible: should be "cdns,xtfpga-spi".
+- reg: physical base address of the controller and length of memory mapped
+  region.

Documentation/devicetree/bindings/spi/spi_altera.txt

@@ -0,0 +1,5 @@
+Altera SPI
+
+Required properties:
+- compatible : should be "ALTR,spi-1.0". <DEPRECATED>
+- compatible : should be "altr,spi-1.0".

Documentation/devicetree/bindings/spi/spi_atmel.txt

@@ -0,0 +1,31 @@
+Atmel SPI device
+
+Required properties:
+- compatible : should be "atmel,at91rm9200-spi".
+- reg: Address and length of the register set for the device
+- interrupts: Should contain spi interrupt
+- cs-gpios: chipselects
+- clock-names: tuple listing input clock names.
+	Required elements: "spi_clk"
+- clocks: phandles to input clocks.
+
+Example:
+
+spi1: spi@fffcc000 {
+	compatible = "atmel,at91rm9200-spi";
+	reg = <0xfffcc000 0x4000>;
+	interrupts = <13 4 5>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clocks = <&spi1_clk>;
+	clock-names = "spi_clk";
+	cs-gpios = <&pioB 3 0>;
+	status = "okay";
+
+	mmc-slot@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		gpios = <&pioC 4 0>;	/* CD */
+		spi-max-frequency = <25000000>;
+	};
+};

Documentation/devicetree/bindings/spi/spi_oc_tiny.txt

@@ -0,0 +1,12 @@
+OpenCores tiny SPI
+
+Required properties:
+- compatible : should be "opencores,tiny-spi-rtlsvn2".
+- gpios : should specify GPIOs used for chipselect.
+Optional properties:
+- clock-frequency : input clock frequency to the core.
+- baud-width: width, in bits, of the programmable divider used to scale
+	the input clock to SCLK.
+
+The clock-frequency and baud-width properties are needed only if the divider
+is programmable. They are not needed if the divider is fixed.

Documentation/devicetree/bindings/spi/spi_pl022.txt

@@ -0,0 +1,70 @@
+ARM PL022 SPI controller
+
+Required properties:
+- compatible : "arm,pl022", "arm,primecell"
+- reg : Offset and length of the register set for the device
+- interrupts : Should contain SPI controller interrupt
+
+Optional properties:
+- num-cs : total number of chipselects
+- cs-gpios : should specify GPIOs used for chipselects.
+  The gpios will be referred to as reg = <index> in the SPI child nodes.
+  If unspecified, a single SPI device without a chip select can be used.
+- pl022,autosuspend-delay : delay in ms following transfer completion before
+			    the runtime power management system suspends the
+			    device. A setting of 0 indicates no delay and the
+                            device will be suspended immediately
+- pl022,rt : indicates the controller should run the message pump with realtime
+             priority to minimise the transfer latency on the bus (boolean)
+- dmas : Two or more DMA channel specifiers following the convention outlined
+         in bindings/dma/dma.txt
+- dma-names: Names for the dma channels, if present. There must be at
+	     least one channel named "tx" for transmit and named "rx" for
+             receive.
+
+
+SPI slave nodes must be children of the SPI master node and can
+contain the following properties.
+
+- pl022,interface : interface type:
+	0: SPI
+	1: Texas Instruments Synchronous Serial Frame Format
+	2: Microwire (Half Duplex)
+- pl022,com-mode : polling, interrupt or dma
+- pl022,rx-level-trig : Rx FIFO watermark level
+- pl022,tx-level-trig : Tx FIFO watermark level
+- pl022,ctrl-len : Microwire interface: Control length
+- pl022,wait-state : Microwire interface: Wait state
+- pl022,duplex : Microwire interface: Full/Half duplex
+
+
+Example:
+
+	spi@e0100000 {
+		compatible = "arm,pl022", "arm,primecell";
+		reg = <0xe0100000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <0 31 0x4>;
+		dmas = <&dma-controller 23 1>,
+			<&dma-controller 24 0>;
+		dma-names = "rx", "tx";
+
+		m25p80@1 {
+			compatible = "st,m25p80";
+			reg = <1>;
+			spi-max-frequency = <12000000>;
+			spi-cpol;
+			spi-cpha;
+			pl022,hierarchy = <0>;
+			pl022,interface = <0>;
+			pl022,slave-tx-disable;
+			pl022,com-mode = <0x2>;
+			pl022,rx-level-trig = <0>;
+			pl022,tx-level-trig = <0>;
+			pl022,ctrl-len = <0x11>;
+			pl022,wait-state = <0>;
+			pl022,duplex = <0>;
+		};
+	};
+	

Documentation/devicetree/bindings/spi/ti_qspi.txt

@@ -0,0 +1,28 @@
+TI QSPI controller.
+
+Required properties:
+- compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi".
+- reg: Should contain QSPI registers location and length.
+- reg-names: Should contain the resource reg names.
+	- qspi_base: Qspi configuration register Address space
+	- qspi_mmap: Memory mapped Address space
+	- (optional) qspi_ctrlmod: Control module Address space
+- interrupts: should contain the qspi interrupt number.
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+- ti,hwmods: Name of the hwmod associated to the QSPI
+
+Recommended properties:
+- spi-max-frequency: Definition as per
+                     Documentation/devicetree/bindings/spi/spi-bus.txt
+
+Example:
+
+qspi: qspi@4b300000 {
+	compatible = "ti,dra7xxx-qspi";
+	reg = <0x47900000 0x100>, <0x30000000 0x3ffffff>;
+	reg-names = "qspi_base", "qspi_mmap";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	spi-max-frequency = <25000000>;
+	ti,hwmods = "qspi";
+};