Fixed MTP to work with TWRP

arch/blackfin/include/asm/bfin5xx_spi.h

@@ -0,0 +1,86 @@
+/*
+ * Blackfin On-Chip SPI Driver
+ *
+ * Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef _SPI_CHANNEL_H_
+#define _SPI_CHANNEL_H_
+
+#define MIN_SPI_BAUD_VAL	2
+
+#define BIT_CTL_ENABLE      0x4000
+#define BIT_CTL_OPENDRAIN   0x2000
+#define BIT_CTL_MASTER      0x1000
+#define BIT_CTL_CPOL        0x0800
+#define BIT_CTL_CPHA        0x0400
+#define BIT_CTL_LSBF        0x0200
+#define BIT_CTL_WORDSIZE    0x0100
+#define BIT_CTL_EMISO       0x0020
+#define BIT_CTL_PSSE        0x0010
+#define BIT_CTL_GM          0x0008
+#define BIT_CTL_SZ          0x0004
+#define BIT_CTL_RXMOD       0x0000
+#define BIT_CTL_TXMOD       0x0001
+#define BIT_CTL_TIMOD_DMA_TX 0x0003
+#define BIT_CTL_TIMOD_DMA_RX 0x0002
+#define BIT_CTL_SENDOPT     0x0004
+#define BIT_CTL_TIMOD       0x0003
+
+#define BIT_STAT_SPIF       0x0001
+#define BIT_STAT_MODF       0x0002
+#define BIT_STAT_TXE        0x0004
+#define BIT_STAT_TXS        0x0008
+#define BIT_STAT_RBSY       0x0010
+#define BIT_STAT_RXS        0x0020
+#define BIT_STAT_TXCOL      0x0040
+#define BIT_STAT_CLR        0xFFFF
+
+#define BIT_STU_SENDOVER    0x0001
+#define BIT_STU_RECVFULL    0x0020
+
+/*
+ * All Blackfin system MMRs are padded to 32bits even if the register
+ * itself is only 16bits.  So use a helper macro to streamline this.
+ */
+#define __BFP(m) u16 m; u16 __pad_##m
+
+/*
+ * bfin spi registers layout
+ */
+struct bfin_spi_regs {
+	__BFP(ctl);
+	__BFP(flg);
+	__BFP(stat);
+	__BFP(tdbr);
+	__BFP(rdbr);
+	__BFP(baud);
+	__BFP(shadow);
+};
+
+#undef __BFP
+
+#define MAX_CTRL_CS          8  /* cs in spi controller */
+
+/* device.platform_data for SSP controller devices */
+struct bfin5xx_spi_master {
+	u16 num_chipselect;
+	u8 enable_dma;
+	u16 pin_req[7];
+};
+
+/* spi_board_info.controller_data for SPI slave devices,
+ * copied to spi_device.platform_data ... mostly for dma tuning
+ */
+struct bfin5xx_spi_chip {
+	u16 ctl_reg;
+	u8 enable_dma;
+	u16 cs_chg_udelay; /* Some devices require 16-bit delays */
+	/* Value to send if no TX value is supplied, usually 0x0 or 0xFFFF */
+	u16 idle_tx_val;
+	u8 pio_interrupt; /* Enable spi data irq */
+};
+
+#endif /* _SPI_CHANNEL_H_ */