Fixed MTP to work with TWRP

drivers/i2c/muxes/Kconfig

@@ -0,0 +1,63 @@
+#
+# Multiplexer I2C chip drivers configuration
+#
+
+menu "Multiplexer I2C Chip support"
+	depends on I2C_MUX
+
+config I2C_ARB_GPIO_CHALLENGE
+	tristate "GPIO-based I2C arbitration"
+	depends on GPIOLIB && OF
+	help
+	  If you say yes to this option, support will be included for an
+	  I2C multimaster arbitration scheme using GPIOs and a challenge &
+	  response mechanism where masters have to claim the bus by asserting
+	  a GPIO.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-arb-gpio-challenge.
+
+config I2C_MUX_GPIO
+	tristate "GPIO-based I2C multiplexer"
+	depends on GPIOLIB
+	help
+	  If you say yes to this option, support will be included for a
+	  GPIO based I2C multiplexer. This driver provides access to
+	  I2C busses connected through a MUX, which is controlled
+	  through GPIO pins.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-mux-gpio.
+
+config I2C_MUX_PCA9541
+	tristate "NXP PCA9541 I2C Master Selector"
+	help
+	  If you say yes here you get support for the NXP PCA9541
+	  I2C Master Selector.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-mux-pca9541.
+
+config I2C_MUX_PCA954x
+	tristate "Philips PCA954x I2C Mux/switches"
+	depends on GPIOLIB
+	help
+	  If you say yes here you get support for the Philips PCA954x
+	  I2C mux/switch devices.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-mux-pca954x.
+
+config I2C_MUX_PINCTRL
+	tristate "pinctrl-based I2C multiplexer"
+	depends on PINCTRL
+	help
+	  If you say yes to this option, support will be included for an I2C
+	  multiplexer that uses the pinctrl subsystem, i.e. pin multiplexing.
+	  This is useful for SoCs whose I2C module's signals can be routed to
+	  different sets of pins at run-time.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called pinctrl-i2cmux.
+
+endmenu

drivers/i2c/muxes/Makefile

@@ -0,0 +1,11 @@
+#
+# Makefile for multiplexer I2C chip drivers.
+
+obj-$(CONFIG_I2C_ARB_GPIO_CHALLENGE)	+= i2c-arb-gpio-challenge.o
+
+obj-$(CONFIG_I2C_MUX_GPIO)	+= i2c-mux-gpio.o
+obj-$(CONFIG_I2C_MUX_PCA9541)	+= i2c-mux-pca9541.o
+obj-$(CONFIG_I2C_MUX_PCA954x)	+= i2c-mux-pca954x.o
+obj-$(CONFIG_I2C_MUX_PINCTRL)	+= i2c-mux-pinctrl.o
+
+ccflags-$(CONFIG_I2C_DEBUG_BUS) := -DDEBUG

drivers/i2c/muxes/i2c-arb-gpio-challenge.c

@@ -0,0 +1,249 @@
+/*
+ * GPIO-based I2C Arbitration Using a Challenge & Response Mechanism
+ *
+ * Copyright (C) 2012 Google, Inc
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/i2c.h>
+#include <linux/i2c-mux.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+
+/**
+ * struct i2c_arbitrator_data - Driver data for I2C arbitrator
+ *
+ * @parent: Parent adapter
+ * @child: Child bus
+ * @our_gpio: GPIO we'll use to claim.
+ * @our_gpio_release: 0 if active high; 1 if active low; AKA if the GPIO ==
+ *   this then consider it released.
+ * @their_gpio: GPIO that the other side will use to claim.
+ * @their_gpio_release: 0 if active high; 1 if active low; AKA if the GPIO ==
+ *   this then consider it released.
+ * @slew_delay_us: microseconds to wait for a GPIO to go high.
+ * @wait_retry_us: we'll attempt another claim after this many microseconds.
+ * @wait_free_us: we'll give up after this many microseconds.
+ */
+
+struct i2c_arbitrator_data {
+	struct i2c_adapter *parent;
+	struct i2c_adapter *child;
+	int our_gpio;
+	int our_gpio_release;
+	int their_gpio;
+	int their_gpio_release;
+	unsigned int slew_delay_us;
+	unsigned int wait_retry_us;
+	unsigned int wait_free_us;
+};
+
+
+/**
+ * i2c_arbitrator_select - claim the I2C bus
+ *
+ * Use the GPIO-based signalling protocol; return -EBUSY if we fail.
+ */
+static int i2c_arbitrator_select(struct i2c_adapter *adap, void *data, u32 chan)
+{
+	const struct i2c_arbitrator_data *arb = data;
+	unsigned long stop_retry, stop_time;
+
+	/* Start a round of trying to claim the bus */
+	stop_time = jiffies + usecs_to_jiffies(arb->wait_free_us) + 1;
+	do {
+		/* Indicate that we want to claim the bus */
+		gpio_set_value(arb->our_gpio, !arb->our_gpio_release);
+		udelay(arb->slew_delay_us);
+
+		/* Wait for the other master to release it */
+		stop_retry = jiffies + usecs_to_jiffies(arb->wait_retry_us) + 1;
+		while (time_before(jiffies, stop_retry)) {
+			int gpio_val = !!gpio_get_value(arb->their_gpio);
+
+			if (gpio_val == arb->their_gpio_release) {
+				/* We got it, so return */
+				return 0;
+			}
+
+			usleep_range(50, 200);
+		}
+
+		/* It didn't release, so give up, wait, and try again */
+		gpio_set_value(arb->our_gpio, arb->our_gpio_release);
+
+		usleep_range(arb->wait_retry_us, arb->wait_retry_us * 2);
+	} while (time_before(jiffies, stop_time));
+
+	/* Give up, release our claim */
+	gpio_set_value(arb->our_gpio, arb->our_gpio_release);
+	udelay(arb->slew_delay_us);
+	dev_err(&adap->dev, "Could not claim bus, timeout\n");
+	return -EBUSY;
+}
+
+/**
+ * i2c_arbitrator_deselect - release the I2C bus
+ *
+ * Release the I2C bus using the GPIO-based signalling protocol.
+ */
+static int i2c_arbitrator_deselect(struct i2c_adapter *adap, void *data,
+				   u32 chan)
+{
+	const struct i2c_arbitrator_data *arb = data;
+
+	/* Release the bus and wait for the other master to notice */
+	gpio_set_value(arb->our_gpio, arb->our_gpio_release);
+	udelay(arb->slew_delay_us);
+
+	return 0;
+}
+
+static int i2c_arbitrator_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *parent_np;
+	struct i2c_arbitrator_data *arb;
+	enum of_gpio_flags gpio_flags;
+	unsigned long out_init;
+	int ret;
+
+	/* We only support probing from device tree; no platform_data */
+	if (!np) {
+		dev_err(dev, "Cannot find device tree node\n");
+		return -ENODEV;
+	}
+	if (dev_get_platdata(dev)) {
+		dev_err(dev, "Platform data is not supported\n");
+		return -EINVAL;
+	}
+
+	arb = devm_kzalloc(dev, sizeof(*arb), GFP_KERNEL);
+	if (!arb) {
+		dev_err(dev, "Cannot allocate i2c_arbitrator_data\n");
+		return -ENOMEM;
+	}
+	platform_set_drvdata(pdev, arb);
+
+	/* Request GPIOs */
+	ret = of_get_named_gpio_flags(np, "our-claim-gpio", 0, &gpio_flags);
+	if (!gpio_is_valid(ret)) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "Error getting our-claim-gpio\n");
+		return ret;
+	}
+	arb->our_gpio = ret;
+	arb->our_gpio_release = !!(gpio_flags & OF_GPIO_ACTIVE_LOW);
+	out_init = (gpio_flags & OF_GPIO_ACTIVE_LOW) ?
+		GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
+	ret = devm_gpio_request_one(dev, arb->our_gpio, out_init,
+				    "our-claim-gpio");
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "Error requesting our-claim-gpio\n");
+		return ret;
+	}
+
+	ret = of_get_named_gpio_flags(np, "their-claim-gpios", 0, &gpio_flags);
+	if (!gpio_is_valid(ret)) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "Error getting their-claim-gpio\n");
+		return ret;
+	}
+	arb->their_gpio = ret;
+	arb->their_gpio_release = !!(gpio_flags & OF_GPIO_ACTIVE_LOW);
+	ret = devm_gpio_request_one(dev, arb->their_gpio, GPIOF_IN,
+				    "their-claim-gpio");
+	if (ret) {
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "Error requesting their-claim-gpio\n");
+		return ret;
+	}
+
+	/* At the moment we only support a single two master (us + 1 other) */
+	if (gpio_is_valid(of_get_named_gpio(np, "their-claim-gpios", 1))) {
+		dev_err(dev, "Only one other master is supported\n");
+		return -EINVAL;
+	}
+
+	/* Arbitration parameters */
+	if (of_property_read_u32(np, "slew-delay-us", &arb->slew_delay_us))
+		arb->slew_delay_us = 10;
+	if (of_property_read_u32(np, "wait-retry-us", &arb->wait_retry_us))
+		arb->wait_retry_us = 3000;
+	if (of_property_read_u32(np, "wait-free-us", &arb->wait_free_us))
+		arb->wait_free_us = 50000;
+
+	/* Find our parent */
+	parent_np = of_parse_phandle(np, "i2c-parent", 0);
+	if (!parent_np) {
+		dev_err(dev, "Cannot parse i2c-parent\n");
+		return -EINVAL;
+	}
+	arb->parent = of_find_i2c_adapter_by_node(parent_np);
+	if (!arb->parent) {
+		dev_err(dev, "Cannot find parent bus\n");
+		return -EPROBE_DEFER;
+	}
+
+	/* Actually add the mux adapter */
+	arb->child = i2c_add_mux_adapter(arb->parent, dev, arb, 0, 0, 0,
+					 i2c_arbitrator_select,
+					 i2c_arbitrator_deselect);
+	if (!arb->child) {
+		dev_err(dev, "Failed to add adapter\n");
+		ret = -ENODEV;
+		i2c_put_adapter(arb->parent);
+	}
+
+	return ret;
+}
+
+static int i2c_arbitrator_remove(struct platform_device *pdev)
+{
+	struct i2c_arbitrator_data *arb = platform_get_drvdata(pdev);
+
+	i2c_del_mux_adapter(arb->child);
+	i2c_put_adapter(arb->parent);
+
+	return 0;
+}
+
+static const struct of_device_id i2c_arbitrator_of_match[] = {
+	{ .compatible = "i2c-arb-gpio-challenge", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, i2c_arbitrator_of_match);
+
+static struct platform_driver i2c_arbitrator_driver = {
+	.probe	= i2c_arbitrator_probe,
+	.remove	= i2c_arbitrator_remove,
+	.driver	= {
+		.owner	= THIS_MODULE,
+		.name	= "i2c-arb-gpio-challenge",
+		.of_match_table = i2c_arbitrator_of_match,
+	},
+};
+
+module_platform_driver(i2c_arbitrator_driver);
+
+MODULE_DESCRIPTION("GPIO-based I2C Arbitration");
+MODULE_AUTHOR("Doug Anderson <dianders@chromium.org>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:i2c-arb-gpio-challenge");

drivers/i2c/muxes/i2c-mux-gpio.c

@@ -0,0 +1,294 @@
+/*
+ * I2C multiplexer using GPIO API
+ *
+ * Peter Korsgaard <peter.korsgaard@barco.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/i2c.h>
+#include <linux/i2c-mux.h>
+#include <linux/i2c-mux-gpio.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
+
+struct gpiomux {
+	struct i2c_adapter *parent;
+	struct i2c_adapter **adap; /* child busses */
+	struct i2c_mux_gpio_platform_data data;
+	unsigned gpio_base;
+};
+
+static void i2c_mux_gpio_set(const struct gpiomux *mux, unsigned val)
+{
+	int i;
+
+	for (i = 0; i < mux->data.n_gpios; i++)
+		gpio_set_value_cansleep(mux->gpio_base + mux->data.gpios[i],
+					val & (1 << i));
+}
+
+static int i2c_mux_gpio_select(struct i2c_adapter *adap, void *data, u32 chan)
+{
+	struct gpiomux *mux = data;
+
+	i2c_mux_gpio_set(mux, chan);
+
+	return 0;
+}
+
+static int i2c_mux_gpio_deselect(struct i2c_adapter *adap, void *data, u32 chan)
+{
+	struct gpiomux *mux = data;
+
+	i2c_mux_gpio_set(mux, mux->data.idle);
+
+	return 0;
+}
+
+static int match_gpio_chip_by_label(struct gpio_chip *chip,
+					      void *data)
+{
+	return !strcmp(chip->label, data);
+}
+
+#ifdef CONFIG_OF
+static int i2c_mux_gpio_probe_dt(struct gpiomux *mux,
+					struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *adapter_np, *child;
+	struct i2c_adapter *adapter;
+	unsigned *values, *gpios;
+	int i = 0, ret;
+
+	if (!np)
+		return -ENODEV;
+
+	adapter_np = of_parse_phandle(np, "i2c-parent", 0);
+	if (!adapter_np) {
+		dev_err(&pdev->dev, "Cannot parse i2c-parent\n");
+		return -ENODEV;
+	}
+	adapter = of_find_i2c_adapter_by_node(adapter_np);
+	if (!adapter) {
+		dev_err(&pdev->dev, "Cannot find parent bus\n");
+		return -EPROBE_DEFER;
+	}
+	mux->data.parent = i2c_adapter_id(adapter);
+	put_device(&adapter->dev);
+
+	mux->data.n_values = of_get_child_count(np);
+
+	values = devm_kzalloc(&pdev->dev,
+			      sizeof(*mux->data.values) * mux->data.n_values,
+			      GFP_KERNEL);
+	if (!values) {
+		dev_err(&pdev->dev, "Cannot allocate values array");
+		return -ENOMEM;
+	}
+
+	for_each_child_of_node(np, child) {
+		of_property_read_u32(child, "reg", values + i);
+		i++;
+	}
+	mux->data.values = values;
+
+	if (of_property_read_u32(np, "idle-state", &mux->data.idle))
+		mux->data.idle = I2C_MUX_GPIO_NO_IDLE;
+
+	mux->data.n_gpios = of_gpio_named_count(np, "mux-gpios");
+	if (mux->data.n_gpios < 0) {
+		dev_err(&pdev->dev, "Missing mux-gpios property in the DT.\n");
+		return -EINVAL;
+	}
+
+	gpios = devm_kzalloc(&pdev->dev,
+			     sizeof(*mux->data.gpios) * mux->data.n_gpios, GFP_KERNEL);
+	if (!gpios) {
+		dev_err(&pdev->dev, "Cannot allocate gpios array");
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < mux->data.n_gpios; i++) {
+		ret = of_get_named_gpio(np, "mux-gpios", i);
+		if (ret < 0)
+			return ret;
+		gpios[i] = ret;
+	}
+
+	mux->data.gpios = gpios;
+
+	return 0;
+}
+#else
+static int i2c_mux_gpio_probe_dt(struct gpiomux *mux,
+					struct platform_device *pdev)
+{
+	return 0;
+}
+#endif
+
+static int i2c_mux_gpio_probe(struct platform_device *pdev)
+{
+	struct gpiomux *mux;
+	struct i2c_adapter *parent;
+	int (*deselect) (struct i2c_adapter *, void *, u32);
+	unsigned initial_state, gpio_base;
+	int i, ret;
+
+	mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
+	if (!mux) {
+		dev_err(&pdev->dev, "Cannot allocate gpiomux structure");
+		return -ENOMEM;
+	}
+
+	platform_set_drvdata(pdev, mux);
+
+	if (!dev_get_platdata(&pdev->dev)) {
+		ret = i2c_mux_gpio_probe_dt(mux, pdev);
+		if (ret < 0)
+			return ret;
+	} else {
+		memcpy(&mux->data, dev_get_platdata(&pdev->dev),
+			sizeof(mux->data));
+	}
+
+	/*
+	 * If a GPIO chip name is provided, the GPIO pin numbers provided are
+	 * relative to its base GPIO number. Otherwise they are absolute.
+	 */
+	if (mux->data.gpio_chip) {
+		struct gpio_chip *gpio;
+
+		gpio = gpiochip_find(mux->data.gpio_chip,
+				     match_gpio_chip_by_label);
+		if (!gpio)
+			return -EPROBE_DEFER;
+
+		gpio_base = gpio->base;
+	} else {
+		gpio_base = 0;
+	}
+
+	parent = i2c_get_adapter(mux->data.parent);
+	if (!parent) {
+		dev_err(&pdev->dev, "Parent adapter (%d) not found\n",
+			mux->data.parent);
+		return -EPROBE_DEFER;
+	}
+
+	mux->parent = parent;
+	mux->gpio_base = gpio_base;
+
+	mux->adap = devm_kzalloc(&pdev->dev,
+				 sizeof(*mux->adap) * mux->data.n_values,
+				 GFP_KERNEL);
+	if (!mux->adap) {
+		dev_err(&pdev->dev, "Cannot allocate i2c_adapter structure");
+		ret = -ENOMEM;
+		goto alloc_failed;
+	}
+
+	if (mux->data.idle != I2C_MUX_GPIO_NO_IDLE) {
+		initial_state = mux->data.idle;
+		deselect = i2c_mux_gpio_deselect;
+	} else {
+		initial_state = mux->data.values[0];
+		deselect = NULL;
+	}
+
+	for (i = 0; i < mux->data.n_gpios; i++) {
+		ret = gpio_request(gpio_base + mux->data.gpios[i], "i2c-mux-gpio");
+		if (ret) {
+			dev_err(&pdev->dev, "Failed to request GPIO %d\n",
+				mux->data.gpios[i]);
+			goto err_request_gpio;
+		}
+
+		ret = gpio_direction_output(gpio_base + mux->data.gpios[i],
+					    initial_state & (1 << i));
+		if (ret) {
+			dev_err(&pdev->dev,
+				"Failed to set direction of GPIO %d to output\n",
+				mux->data.gpios[i]);
+			i++;	/* gpio_request above succeeded, so must free */
+			goto err_request_gpio;
+		}
+	}
+
+	for (i = 0; i < mux->data.n_values; i++) {
+		u32 nr = mux->data.base_nr ? (mux->data.base_nr + i) : 0;
+		unsigned int class = mux->data.classes ? mux->data.classes[i] : 0;
+
+		mux->adap[i] = i2c_add_mux_adapter(parent, &pdev->dev, mux, nr,
+						   mux->data.values[i], class,
+						   i2c_mux_gpio_select, deselect);
+		if (!mux->adap[i]) {
+			ret = -ENODEV;
+			dev_err(&pdev->dev, "Failed to add adapter %d\n", i);
+			goto add_adapter_failed;
+		}
+	}
+
+	dev_info(&pdev->dev, "%d port mux on %s adapter\n",
+		 mux->data.n_values, parent->name);
+
+	return 0;
+
+add_adapter_failed:
+	for (; i > 0; i--)
+		i2c_del_mux_adapter(mux->adap[i - 1]);
+	i = mux->data.n_gpios;
+err_request_gpio:
+	for (; i > 0; i--)
+		gpio_free(gpio_base + mux->data.gpios[i - 1]);
+alloc_failed:
+	i2c_put_adapter(parent);
+
+	return ret;
+}
+
+static int i2c_mux_gpio_remove(struct platform_device *pdev)
+{
+	struct gpiomux *mux = platform_get_drvdata(pdev);
+	int i;
+
+	for (i = 0; i < mux->data.n_values; i++)
+		i2c_del_mux_adapter(mux->adap[i]);
+
+	for (i = 0; i < mux->data.n_gpios; i++)
+		gpio_free(mux->gpio_base + mux->data.gpios[i]);
+
+	i2c_put_adapter(mux->parent);
+
+	return 0;
+}
+
+static const struct of_device_id i2c_mux_gpio_of_match[] = {
+	{ .compatible = "i2c-mux-gpio", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, i2c_mux_gpio_of_match);
+
+static struct platform_driver i2c_mux_gpio_driver = {
+	.probe	= i2c_mux_gpio_probe,
+	.remove	= i2c_mux_gpio_remove,
+	.driver	= {
+		.owner	= THIS_MODULE,
+		.name	= "i2c-mux-gpio",
+		.of_match_table = i2c_mux_gpio_of_match,
+	},
+};
+
+module_platform_driver(i2c_mux_gpio_driver);
+
+MODULE_DESCRIPTION("GPIO-based I2C multiplexer driver");
+MODULE_AUTHOR("Peter Korsgaard <peter.korsgaard@barco.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:i2c-mux-gpio");

drivers/i2c/muxes/i2c-mux-pca9541.c

@@ -0,0 +1,400 @@
+/*
+ * I2C multiplexer driver for PCA9541 bus master selector
+ *
+ * Copyright (c) 2010 Ericsson AB.
+ *
+ * Author: Guenter Roeck <linux@roeck-us.net>
+ *
+ * Derived from:
+ *  pca954x.c
+ *
+ *  Copyright (c) 2008-2009 Rodolfo Giometti <giometti@linux.it>
+ *  Copyright (c) 2008-2009 Eurotech S.p.A. <info@eurotech.it>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/jiffies.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/i2c-mux.h>
+
+#include <linux/i2c/pca954x.h>
+
+/*
+ * The PCA9541 is a bus master selector. It supports two I2C masters connected
+ * to a single slave bus.
+ *
+ * Before each bus transaction, a master has to acquire bus ownership. After the
+ * transaction is complete, bus ownership has to be released. This fits well
+ * into the I2C multiplexer framework, which provides select and release
+ * functions for this purpose. For this reason, this driver is modeled as
+ * single-channel I2C bus multiplexer.
+ *
+ * This driver assumes that the two bus masters are controlled by two different
+ * hosts. If a single host controls both masters, platform code has to ensure
+ * that only one of the masters is instantiated at any given time.
+ */
+
+#define PCA9541_CONTROL		0x01
+#define PCA9541_ISTAT		0x02
+
+#define PCA9541_CTL_MYBUS	(1 << 0)
+#define PCA9541_CTL_NMYBUS	(1 << 1)
+#define PCA9541_CTL_BUSON	(1 << 2)
+#define PCA9541_CTL_NBUSON	(1 << 3)
+#define PCA9541_CTL_BUSINIT	(1 << 4)
+#define PCA9541_CTL_TESTON	(1 << 6)
+#define PCA9541_CTL_NTESTON	(1 << 7)
+
+#define PCA9541_ISTAT_INTIN	(1 << 0)
+#define PCA9541_ISTAT_BUSINIT	(1 << 1)
+#define PCA9541_ISTAT_BUSOK	(1 << 2)
+#define PCA9541_ISTAT_BUSLOST	(1 << 3)
+#define PCA9541_ISTAT_MYTEST	(1 << 6)
+#define PCA9541_ISTAT_NMYTEST	(1 << 7)
+
+#define BUSON		(PCA9541_CTL_BUSON | PCA9541_CTL_NBUSON)
+#define MYBUS		(PCA9541_CTL_MYBUS | PCA9541_CTL_NMYBUS)
+#define mybus(x)	(!((x) & MYBUS) || ((x) & MYBUS) == MYBUS)
+#define busoff(x)	(!((x) & BUSON) || ((x) & BUSON) == BUSON)
+
+/* arbitration timeouts, in jiffies */
+#define ARB_TIMEOUT	(HZ / 8)	/* 125 ms until forcing bus ownership */
+#define ARB2_TIMEOUT	(HZ / 4)	/* 250 ms until acquisition failure */
+
+/* arbitration retry delays, in us */
+#define SELECT_DELAY_SHORT	50
+#define SELECT_DELAY_LONG	1000
+
+struct pca9541 {
+	struct i2c_adapter *mux_adap;
+	unsigned long select_timeout;
+	unsigned long arb_timeout;
+};
+
+static const struct i2c_device_id pca9541_id[] = {
+	{"pca9541", 0},
+	{}
+};
+
+MODULE_DEVICE_TABLE(i2c, pca9541_id);
+
+/*
+ * Write to chip register. Don't use i2c_transfer()/i2c_smbus_xfer()
+ * as they will try to lock the adapter a second time.
+ */
+static int pca9541_reg_write(struct i2c_client *client, u8 command, u8 val)
+{
+	struct i2c_adapter *adap = client->adapter;
+	int ret;
+
+	if (adap->algo->master_xfer) {
+		struct i2c_msg msg;
+		char buf[2];
+
+		msg.addr = client->addr;
+		msg.flags = 0;
+		msg.len = 2;
+		buf[0] = command;
+		buf[1] = val;
+		msg.buf = buf;
+		ret = adap->algo->master_xfer(adap, &msg, 1);
+	} else {
+		union i2c_smbus_data data;
+
+		data.byte = val;
+		ret = adap->algo->smbus_xfer(adap, client->addr,
+					     client->flags,
+					     I2C_SMBUS_WRITE,
+					     command,
+					     I2C_SMBUS_BYTE_DATA, &data);
+	}
+
+	return ret;
+}
+
+/*
+ * Read from chip register. Don't use i2c_transfer()/i2c_smbus_xfer()
+ * as they will try to lock adapter a second time.
+ */
+static int pca9541_reg_read(struct i2c_client *client, u8 command)
+{
+	struct i2c_adapter *adap = client->adapter;
+	int ret;
+	u8 val;
+
+	if (adap->algo->master_xfer) {
+		struct i2c_msg msg[2] = {
+			{
+				.addr = client->addr,
+				.flags = 0,
+				.len = 1,
+				.buf = &command
+			},
+			{
+				.addr = client->addr,
+				.flags = I2C_M_RD,
+				.len = 1,
+				.buf = &val
+			}
+		};
+		ret = adap->algo->master_xfer(adap, msg, 2);
+		if (ret == 2)
+			ret = val;
+		else if (ret >= 0)
+			ret = -EIO;
+	} else {
+		union i2c_smbus_data data;
+
+		ret = adap->algo->smbus_xfer(adap, client->addr,
+					     client->flags,
+					     I2C_SMBUS_READ,
+					     command,
+					     I2C_SMBUS_BYTE_DATA, &data);
+		if (!ret)
+			ret = data.byte;
+	}
+	return ret;
+}
+
+/*
+ * Arbitration management functions
+ */
+
+/* Release bus. Also reset NTESTON and BUSINIT if it was set. */
+static void pca9541_release_bus(struct i2c_client *client)
+{
+	int reg;
+
+	reg = pca9541_reg_read(client, PCA9541_CONTROL);
+	if (reg >= 0 && !busoff(reg) && mybus(reg))
+		pca9541_reg_write(client, PCA9541_CONTROL,
+				  (reg & PCA9541_CTL_NBUSON) >> 1);
+}
+
+/*
+ * Arbitration is defined as a two-step process. A bus master can only activate
+ * the slave bus if it owns it; otherwise it has to request ownership first.
+ * This multi-step process ensures that access contention is resolved
+ * gracefully.
+ *
+ * Bus	Ownership	Other master	Action
+ * state		requested access
+ * ----------------------------------------------------
+ * off	-		yes		wait for arbitration timeout or
+ *					for other master to drop request
+ * off	no		no		take ownership
+ * off	yes		no		turn on bus
+ * on	yes		-		done
+ * on	no		-		wait for arbitration timeout or
+ *					for other master to release bus
+ *
+ * The main contention point occurs if the slave bus is off and both masters
+ * request ownership at the same time. In this case, one master will turn on
+ * the slave bus, believing that it owns it. The other master will request
+ * bus ownership. Result is that the bus is turned on, and master which did
+ * _not_ own the slave bus before ends up owning it.
+ */
+
+/* Control commands per PCA9541 datasheet */
+static const u8 pca9541_control[16] = {
+	4, 0, 1, 5, 4, 4, 5, 5, 0, 0, 1, 1, 0, 4, 5, 1
+};
+
+/*
+ * Channel arbitration
+ *
+ * Return values:
+ *  <0: error
+ *  0 : bus not acquired
+ *  1 : bus acquired
+ */
+static int pca9541_arbitrate(struct i2c_client *client)
+{
+	struct pca9541 *data = i2c_get_clientdata(client);
+	int reg;
+
+	reg = pca9541_reg_read(client, PCA9541_CONTROL);
+	if (reg < 0)
+		return reg;
+
+	if (busoff(reg)) {
+		int istat;
+		/*
+		 * Bus is off. Request ownership or turn it on unless
+		 * other master requested ownership.
+		 */
+		istat = pca9541_reg_read(client, PCA9541_ISTAT);
+		if (!(istat & PCA9541_ISTAT_NMYTEST)
+		    || time_is_before_eq_jiffies(data->arb_timeout)) {
+			/*
+			 * Other master did not request ownership,
+			 * or arbitration timeout expired. Take the bus.
+			 */
+			pca9541_reg_write(client,
+					  PCA9541_CONTROL,
+					  pca9541_control[reg & 0x0f]
+					  | PCA9541_CTL_NTESTON);
+			data->select_timeout = SELECT_DELAY_SHORT;
+		} else {
+			/*
+			 * Other master requested ownership.
+			 * Set extra long timeout to give it time to acquire it.
+			 */
+			data->select_timeout = SELECT_DELAY_LONG * 2;
+		}
+	} else if (mybus(reg)) {
+		/*
+		 * Bus is on, and we own it. We are done with acquisition.
+		 * Reset NTESTON and BUSINIT, then return success.
+		 */
+		if (reg & (PCA9541_CTL_NTESTON | PCA9541_CTL_BUSINIT))
+			pca9541_reg_write(client,
+					  PCA9541_CONTROL,
+					  reg & ~(PCA9541_CTL_NTESTON
+						  | PCA9541_CTL_BUSINIT));
+		return 1;
+	} else {
+		/*
+		 * Other master owns the bus.
+		 * If arbitration timeout has expired, force ownership.
+		 * Otherwise request it.
+		 */
+		data->select_timeout = SELECT_DELAY_LONG;
+		if (time_is_before_eq_jiffies(data->arb_timeout)) {
+			/* Time is up, take the bus and reset it. */
+			pca9541_reg_write(client,
+					  PCA9541_CONTROL,
+					  pca9541_control[reg & 0x0f]
+					  | PCA9541_CTL_BUSINIT
+					  | PCA9541_CTL_NTESTON);
+		} else {
+			/* Request bus ownership if needed */
+			if (!(reg & PCA9541_CTL_NTESTON))
+				pca9541_reg_write(client,
+						  PCA9541_CONTROL,
+						  reg | PCA9541_CTL_NTESTON);
+		}
+	}
+	return 0;
+}
+
+static int pca9541_select_chan(struct i2c_adapter *adap, void *client, u32 chan)
+{
+	struct pca9541 *data = i2c_get_clientdata(client);
+	int ret;
+	unsigned long timeout = jiffies + ARB2_TIMEOUT;
+		/* give up after this time */
+
+	data->arb_timeout = jiffies + ARB_TIMEOUT;
+		/* force bus ownership after this time */
+
+	do {
+		ret = pca9541_arbitrate(client);
+		if (ret)
+			return ret < 0 ? ret : 0;
+
+		if (data->select_timeout == SELECT_DELAY_SHORT)
+			udelay(data->select_timeout);
+		else
+			msleep(data->select_timeout / 1000);
+	} while (time_is_after_eq_jiffies(timeout));
+
+	return -ETIMEDOUT;
+}
+
+static int pca9541_release_chan(struct i2c_adapter *adap,
+				void *client, u32 chan)
+{
+	pca9541_release_bus(client);
+	return 0;
+}
+
+/*
+ * I2C init/probing/exit functions
+ */
+static int pca9541_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct i2c_adapter *adap = client->adapter;
+	struct pca954x_platform_data *pdata = dev_get_platdata(&client->dev);
+	struct pca9541 *data;
+	int force;
+	int ret = -ENODEV;
+
+	if (!i2c_check_functionality(adap, I2C_FUNC_SMBUS_BYTE_DATA))
+		goto err;
+
+	data = kzalloc(sizeof(struct pca9541), GFP_KERNEL);
+	if (!data) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	i2c_set_clientdata(client, data);
+
+	/*
+	 * I2C accesses are unprotected here.
+	 * We have to lock the adapter before releasing the bus.
+	 */
+	i2c_lock_adapter(adap);
+	pca9541_release_bus(client);
+	i2c_unlock_adapter(adap);
+
+	/* Create mux adapter */
+
+	force = 0;
+	if (pdata)
+		force = pdata->modes[0].adap_id;
+	data->mux_adap = i2c_add_mux_adapter(adap, &client->dev, client,
+					     force, 0, 0,
+					     pca9541_select_chan,
+					     pca9541_release_chan);
+
+	if (data->mux_adap == NULL) {
+		dev_err(&client->dev, "failed to register master selector\n");
+		goto exit_free;
+	}
+
+	dev_info(&client->dev, "registered master selector for I2C %s\n",
+		 client->name);
+
+	return 0;
+
+exit_free:
+	kfree(data);
+err:
+	return ret;
+}
+
+static int pca9541_remove(struct i2c_client *client)
+{
+	struct pca9541 *data = i2c_get_clientdata(client);
+
+	i2c_del_mux_adapter(data->mux_adap);
+
+	kfree(data);
+	return 0;
+}
+
+static struct i2c_driver pca9541_driver = {
+	.driver = {
+		   .name = "pca9541",
+		   .owner = THIS_MODULE,
+		   },
+	.probe = pca9541_probe,
+	.remove = pca9541_remove,
+	.id_table = pca9541_id,
+};
+
+module_i2c_driver(pca9541_driver);
+
+MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>");
+MODULE_DESCRIPTION("PCA9541 I2C master selector driver");
+MODULE_LICENSE("GPL v2");

drivers/i2c/muxes/i2c-mux-pca954x.c

@@ -0,0 +1,305 @@
+/*
+ * I2C multiplexer
+ *
+ * Copyright (c) 2008-2009 Rodolfo Giometti <giometti@linux.it>
+ * Copyright (c) 2008-2009 Eurotech S.p.A. <info@eurotech.it>
+ *
+ * This module supports the PCA954x series of I2C multiplexer/switch chips
+ * made by Philips Semiconductors.
+ * This includes the:
+ *	 PCA9540, PCA9542, PCA9543, PCA9544, PCA9545, PCA9546, PCA9547
+ *	 and PCA9548.
+ *
+ * These chips are all controlled via the I2C bus itself, and all have a
+ * single 8-bit register. The upstream "parent" bus fans out to two,
+ * four, or eight downstream busses or channels; which of these
+ * are selected is determined by the chip type and register contents. A
+ * mux can select only one sub-bus at a time; a switch can select any
+ * combination simultaneously.
+ *
+ * Based on:
+ *	pca954x.c from Kumar Gala <galak@kernel.crashing.org>
+ * Copyright (C) 2006
+ *
+ * Based on:
+ *	pca954x.c from Ken Harrenstien
+ * Copyright (C) 2004 Google, Inc. (Ken Harrenstien)
+ *
+ * Based on:
+ *	i2c-virtual_cb.c from Brian Kuschak <bkuschak@yahoo.com>
+ * and
+ *	pca9540.c from Jean Delvare <jdelvare@suse.de>.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/i2c-mux.h>
+#include <linux/i2c/pca954x.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/slab.h>
+
+#define PCA954X_MAX_NCHANS 8
+
+enum pca_type {
+	pca_9540,
+	pca_9542,
+	pca_9543,
+	pca_9544,
+	pca_9545,
+	pca_9546,
+	pca_9547,
+	pca_9548,
+};
+
+struct pca954x {
+	enum pca_type type;
+	struct i2c_adapter *virt_adaps[PCA954X_MAX_NCHANS];
+
+	u8 last_chan;		/* last register value */
+};
+
+struct chip_desc {
+	u8 nchans;
+	u8 enable;	/* used for muxes only */
+	enum muxtype {
+		pca954x_ismux = 0,
+		pca954x_isswi
+	} muxtype;
+};
+
+/* Provide specs for the PCA954x types we know about */
+static const struct chip_desc chips[] = {
+	[pca_9540] = {
+		.nchans = 2,
+		.enable = 0x4,
+		.muxtype = pca954x_ismux,
+	},
+	[pca_9543] = {
+		.nchans = 2,
+		.muxtype = pca954x_isswi,
+	},
+	[pca_9544] = {
+		.nchans = 4,
+		.enable = 0x4,
+		.muxtype = pca954x_ismux,
+	},
+	[pca_9545] = {
+		.nchans = 4,
+		.muxtype = pca954x_isswi,
+	},
+	[pca_9547] = {
+		.nchans = 8,
+		.enable = 0x8,
+		.muxtype = pca954x_ismux,
+	},
+	[pca_9548] = {
+		.nchans = 8,
+		.muxtype = pca954x_isswi,
+	},
+};
+
+static const struct i2c_device_id pca954x_id[] = {
+	{ "pca9540", pca_9540 },
+	{ "pca9542", pca_9540 },
+	{ "pca9543", pca_9543 },
+	{ "pca9544", pca_9544 },
+	{ "pca9545", pca_9545 },
+	{ "pca9546", pca_9545 },
+	{ "pca9547", pca_9547 },
+	{ "pca9548", pca_9548 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, pca954x_id);
+
+/* Write to mux register. Don't use i2c_transfer()/i2c_smbus_xfer()
+   for this as they will try to lock adapter a second time */
+static int pca954x_reg_write(struct i2c_adapter *adap,
+			     struct i2c_client *client, u8 val)
+{
+	int ret = -ENODEV;
+
+	if (adap->algo->master_xfer) {
+		struct i2c_msg msg;
+		char buf[1];
+
+		msg.addr = client->addr;
+		msg.flags = 0;
+		msg.len = 1;
+		buf[0] = val;
+		msg.buf = buf;
+		ret = adap->algo->master_xfer(adap, &msg, 1);
+	} else {
+		union i2c_smbus_data data;
+		ret = adap->algo->smbus_xfer(adap, client->addr,
+					     client->flags,
+					     I2C_SMBUS_WRITE,
+					     val, I2C_SMBUS_BYTE, &data);
+	}
+
+	return ret;
+}
+
+static int pca954x_select_chan(struct i2c_adapter *adap,
+			       void *client, u32 chan)
+{
+	struct pca954x *data = i2c_get_clientdata(client);
+	const struct chip_desc *chip = &chips[data->type];
+	u8 regval;
+	int ret = 0;
+
+	/* we make switches look like muxes, not sure how to be smarter */
+	if (chip->muxtype == pca954x_ismux)
+		regval = chan | chip->enable;
+	else
+		regval = 1 << chan;
+
+	/* Only select the channel if its different from the last channel */
+	if (data->last_chan != regval) {
+		ret = pca954x_reg_write(adap, client, regval);
+		data->last_chan = regval;
+	}
+
+	return ret;
+}
+
+static int pca954x_deselect_mux(struct i2c_adapter *adap,
+				void *client, u32 chan)
+{
+	struct pca954x *data = i2c_get_clientdata(client);
+
+	/* Deselect active channel */
+	data->last_chan = 0;
+	return pca954x_reg_write(adap, client, data->last_chan);
+}
+
+/*
+ * I2C init/probing/exit functions
+ */
+static int pca954x_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct i2c_adapter *adap = to_i2c_adapter(client->dev.parent);
+	struct pca954x_platform_data *pdata = dev_get_platdata(&client->dev);
+	struct gpio_desc *gpio;
+	int num, force, class;
+	struct pca954x *data;
+	int ret;
+
+	if (!i2c_check_functionality(adap, I2C_FUNC_SMBUS_BYTE))
+		return -ENODEV;
+
+	data = devm_kzalloc(&client->dev, sizeof(struct pca954x), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, data);
+
+	/* Get the mux out of reset if a reset GPIO is specified. */
+	gpio = devm_gpiod_get(&client->dev, "reset");
+	if (!IS_ERR(gpio))
+		gpiod_direction_output(gpio, 0);
+
+	/* Write the mux register at addr to verify
+	 * that the mux is in fact present. This also
+	 * initializes the mux to disconnected state.
+	 */
+	if (i2c_smbus_write_byte(client, 0) < 0) {
+		dev_warn(&client->dev, "probe failed\n");
+		return -ENODEV;
+	}
+
+	data->type = id->driver_data;
+	data->last_chan = 0;		   /* force the first selection */
+
+	/* Now create an adapter for each channel */
+	for (num = 0; num < chips[data->type].nchans; num++) {
+		force = 0;			  /* dynamic adap number */
+		class = 0;			  /* no class by default */
+		if (pdata) {
+			if (num < pdata->num_modes) {
+				/* force static number */
+				force = pdata->modes[num].adap_id;
+				class = pdata->modes[num].class;
+			} else
+				/* discard unconfigured channels */
+				break;
+		}
+
+		data->virt_adaps[num] =
+			i2c_add_mux_adapter(adap, &client->dev, client,
+				force, num, class, pca954x_select_chan,
+				(pdata && pdata->modes[num].deselect_on_exit)
+					? pca954x_deselect_mux : NULL);
+
+		if (data->virt_adaps[num] == NULL) {
+			ret = -ENODEV;
+			dev_err(&client->dev,
+				"failed to register multiplexed adapter"
+				" %d as bus %d\n", num, force);
+			goto virt_reg_failed;
+		}
+	}
+
+	dev_info(&client->dev,
+		 "registered %d multiplexed busses for I2C %s %s\n",
+		 num, chips[data->type].muxtype == pca954x_ismux
+				? "mux" : "switch", client->name);
+
+	return 0;
+
+virt_reg_failed:
+	for (num--; num >= 0; num--)
+		i2c_del_mux_adapter(data->virt_adaps[num]);
+	return ret;
+}
+
+static int pca954x_remove(struct i2c_client *client)
+{
+	struct pca954x *data = i2c_get_clientdata(client);
+	const struct chip_desc *chip = &chips[data->type];
+	int i;
+
+	for (i = 0; i < chip->nchans; ++i)
+		if (data->virt_adaps[i]) {
+			i2c_del_mux_adapter(data->virt_adaps[i]);
+			data->virt_adaps[i] = NULL;
+		}
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int pca954x_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct pca954x *data = i2c_get_clientdata(client);
+
+	data->last_chan = 0;
+	return i2c_smbus_write_byte(client, 0);
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(pca954x_pm, NULL, pca954x_resume);
+
+static struct i2c_driver pca954x_driver = {
+	.driver		= {
+		.name	= "pca954x",
+		.pm	= &pca954x_pm,
+		.owner	= THIS_MODULE,
+	},
+	.probe		= pca954x_probe,
+	.remove		= pca954x_remove,
+	.id_table	= pca954x_id,
+};
+
+module_i2c_driver(pca954x_driver);
+
+MODULE_AUTHOR("Rodolfo Giometti <giometti@linux.it>");
+MODULE_DESCRIPTION("PCA954x I2C mux/switch driver");
+MODULE_LICENSE("GPL v2");

drivers/i2c/muxes/i2c-mux-pinctrl.c

@@ -0,0 +1,278 @@
+/*
+ * I2C multiplexer using pinctrl API
+ *
+ * Copyright (c) 2012, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/i2c.h>
+#include <linux/i2c-mux.h>
+#include <linux/module.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/i2c-mux-pinctrl.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+
+struct i2c_mux_pinctrl {
+	struct device *dev;
+	struct i2c_mux_pinctrl_platform_data *pdata;
+	struct pinctrl *pinctrl;
+	struct pinctrl_state **states;
+	struct pinctrl_state *state_idle;
+	struct i2c_adapter *parent;
+	struct i2c_adapter **busses;
+};
+
+static int i2c_mux_pinctrl_select(struct i2c_adapter *adap, void *data,
+				  u32 chan)
+{
+	struct i2c_mux_pinctrl *mux = data;
+
+	return pinctrl_select_state(mux->pinctrl, mux->states[chan]);
+}
+
+static int i2c_mux_pinctrl_deselect(struct i2c_adapter *adap, void *data,
+				    u32 chan)
+{
+	struct i2c_mux_pinctrl *mux = data;
+
+	return pinctrl_select_state(mux->pinctrl, mux->state_idle);
+}
+
+#ifdef CONFIG_OF
+static int i2c_mux_pinctrl_parse_dt(struct i2c_mux_pinctrl *mux,
+				struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	int num_names, i, ret;
+	struct device_node *adapter_np;
+	struct i2c_adapter *adapter;
+
+	if (!np)
+		return 0;
+
+	mux->pdata = devm_kzalloc(&pdev->dev, sizeof(*mux->pdata), GFP_KERNEL);
+	if (!mux->pdata) {
+		dev_err(mux->dev,
+			"Cannot allocate i2c_mux_pinctrl_platform_data\n");
+		return -ENOMEM;
+	}
+
+	num_names = of_property_count_strings(np, "pinctrl-names");
+	if (num_names < 0) {
+		dev_err(mux->dev, "Cannot parse pinctrl-names: %d\n",
+			num_names);
+		return num_names;
+	}
+
+	mux->pdata->pinctrl_states = devm_kzalloc(&pdev->dev,
+		sizeof(*mux->pdata->pinctrl_states) * num_names,
+		GFP_KERNEL);
+	if (!mux->pdata->pinctrl_states) {
+		dev_err(mux->dev, "Cannot allocate pinctrl_states\n");
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < num_names; i++) {
+		ret = of_property_read_string_index(np, "pinctrl-names", i,
+			&mux->pdata->pinctrl_states[mux->pdata->bus_count]);
+		if (ret < 0) {
+			dev_err(mux->dev, "Cannot parse pinctrl-names: %d\n",
+				ret);
+			return ret;
+		}
+		if (!strcmp(mux->pdata->pinctrl_states[mux->pdata->bus_count],
+			    "idle")) {
+			if (i != num_names - 1) {
+				dev_err(mux->dev, "idle state must be last\n");
+				return -EINVAL;
+			}
+			mux->pdata->pinctrl_state_idle = "idle";
+		} else {
+			mux->pdata->bus_count++;
+		}
+	}
+
+	adapter_np = of_parse_phandle(np, "i2c-parent", 0);
+	if (!adapter_np) {
+		dev_err(mux->dev, "Cannot parse i2c-parent\n");
+		return -ENODEV;
+	}
+	adapter = of_find_i2c_adapter_by_node(adapter_np);
+	if (!adapter) {
+		dev_err(mux->dev, "Cannot find parent bus\n");
+		return -EPROBE_DEFER;
+	}
+	mux->pdata->parent_bus_num = i2c_adapter_id(adapter);
+	put_device(&adapter->dev);
+
+	return 0;
+}
+#else
+static inline int i2c_mux_pinctrl_parse_dt(struct i2c_mux_pinctrl *mux,
+					   struct platform_device *pdev)
+{
+	return 0;
+}
+#endif
+
+static int i2c_mux_pinctrl_probe(struct platform_device *pdev)
+{
+	struct i2c_mux_pinctrl *mux;
+	int (*deselect)(struct i2c_adapter *, void *, u32);
+	int i, ret;
+
+	mux = devm_kzalloc(&pdev->dev, sizeof(*mux), GFP_KERNEL);
+	if (!mux) {
+		dev_err(&pdev->dev, "Cannot allocate i2c_mux_pinctrl\n");
+		ret = -ENOMEM;
+		goto err;
+	}
+	platform_set_drvdata(pdev, mux);
+
+	mux->dev = &pdev->dev;
+
+	mux->pdata = dev_get_platdata(&pdev->dev);
+	if (!mux->pdata) {
+		ret = i2c_mux_pinctrl_parse_dt(mux, pdev);
+		if (ret < 0)
+			goto err;
+	}
+	if (!mux->pdata) {
+		dev_err(&pdev->dev, "Missing platform data\n");
+		ret = -ENODEV;
+		goto err;
+	}
+
+	mux->states = devm_kzalloc(&pdev->dev,
+				   sizeof(*mux->states) * mux->pdata->bus_count,
+				   GFP_KERNEL);
+	if (!mux->states) {
+		dev_err(&pdev->dev, "Cannot allocate states\n");
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	mux->busses = devm_kzalloc(&pdev->dev,
+				   sizeof(*mux->busses) * mux->pdata->bus_count,
+				   GFP_KERNEL);
+	if (!mux->busses) {
+		dev_err(&pdev->dev, "Cannot allocate busses\n");
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	mux->pinctrl = devm_pinctrl_get(&pdev->dev);
+	if (IS_ERR(mux->pinctrl)) {
+		ret = PTR_ERR(mux->pinctrl);
+		dev_err(&pdev->dev, "Cannot get pinctrl: %d\n", ret);
+		goto err;
+	}
+	for (i = 0; i < mux->pdata->bus_count; i++) {
+		mux->states[i] = pinctrl_lookup_state(mux->pinctrl,
+						mux->pdata->pinctrl_states[i]);
+			if (IS_ERR(mux->states[i])) {
+				ret = PTR_ERR(mux->states[i]);
+				dev_err(&pdev->dev,
+					"Cannot look up pinctrl state %s: %d\n",
+					mux->pdata->pinctrl_states[i], ret);
+				goto err;
+			}
+	}
+	if (mux->pdata->pinctrl_state_idle) {
+		mux->state_idle = pinctrl_lookup_state(mux->pinctrl,
+						mux->pdata->pinctrl_state_idle);
+		if (IS_ERR(mux->state_idle)) {
+			ret = PTR_ERR(mux->state_idle);
+			dev_err(&pdev->dev,
+				"Cannot look up pinctrl state %s: %d\n",
+				mux->pdata->pinctrl_state_idle, ret);
+			goto err;
+		}
+
+		deselect = i2c_mux_pinctrl_deselect;
+	} else {
+		deselect = NULL;
+	}
+
+	mux->parent = i2c_get_adapter(mux->pdata->parent_bus_num);
+	if (!mux->parent) {
+		dev_err(&pdev->dev, "Parent adapter (%d) not found\n",
+			mux->pdata->parent_bus_num);
+		ret = -EPROBE_DEFER;
+		goto err;
+	}
+
+	for (i = 0; i < mux->pdata->bus_count; i++) {
+		u32 bus = mux->pdata->base_bus_num ?
+				(mux->pdata->base_bus_num + i) : 0;
+
+		mux->busses[i] = i2c_add_mux_adapter(mux->parent, &pdev->dev,
+						     mux, bus, i, 0,
+						     i2c_mux_pinctrl_select,
+						     deselect);
+		if (!mux->busses[i]) {
+			ret = -ENODEV;
+			dev_err(&pdev->dev, "Failed to add adapter %d\n", i);
+			goto err_del_adapter;
+		}
+	}
+
+	return 0;
+
+err_del_adapter:
+	for (; i > 0; i--)
+		i2c_del_mux_adapter(mux->busses[i - 1]);
+	i2c_put_adapter(mux->parent);
+err:
+	return ret;
+}
+
+static int i2c_mux_pinctrl_remove(struct platform_device *pdev)
+{
+	struct i2c_mux_pinctrl *mux = platform_get_drvdata(pdev);
+	int i;
+
+	for (i = 0; i < mux->pdata->bus_count; i++)
+		i2c_del_mux_adapter(mux->busses[i]);
+
+	i2c_put_adapter(mux->parent);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id i2c_mux_pinctrl_of_match[] = {
+	{ .compatible = "i2c-mux-pinctrl", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, i2c_mux_pinctrl_of_match);
+#endif
+
+static struct platform_driver i2c_mux_pinctrl_driver = {
+	.driver	= {
+		.name	= "i2c-mux-pinctrl",
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(i2c_mux_pinctrl_of_match),
+	},
+	.probe	= i2c_mux_pinctrl_probe,
+	.remove	= i2c_mux_pinctrl_remove,
+};
+module_platform_driver(i2c_mux_pinctrl_driver);
+
+MODULE_DESCRIPTION("pinctrl-based I2C multiplexer driver");
+MODULE_AUTHOR("Stephen Warren <swarren@nvidia.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:i2c-mux-pinctrl");